U108
Rod-L Electronics M100DC-5.5-5 DC Hipot Tester Output Voltage: 0-5.5KVDC. Output Current: 0-5mA. Ramp Time: 50v/sec to 5000v/sec. Test Time: 1s to 90sec. Detects and Indicates chassis ground, test in progress, test passed, test failed. Full compliance with UL, VDE, BSI, IEC, CSA, and other test http://www.kandelelex.com/jpegs/rdlm100dc-5.5-5.jpg in stock
Rod-L Electronics M1088 IEEE-488 Bus Interface Provides GP-IB interfacing between computer/controllers and Rod-L hipot, ground continuity, and insulation testers. Option 19 required on testers. in stock
Rod-L Electronics M25 Ground Continuity Tester Performs ground continuity tests in compliance with BSI, VDE, CSA, and IEC regulations. Output: 2.5 volts AC, up to 25 amps. Variable test times adjustable from 1 second to 90 seconds. Failures are identified by audible and visual alarms. http://www.kandelelex.com/jpegs/rdlm25.jpg in stock
Rod-L Electronics M30 30 Amp Ground Continuity Tester Performs ground continuity tests in full compliance with BSI, VDE, and IEC. Test time is adjustable from 1 second to 90 seconds. Output Current: 30 amperes. Resistance: 0 to 0.15 ohms, accurate to 5% fs. Test Time: 1 second to 90 seconds. http://www.kandelelex.com/jpegs/rdlm30.jpg in stock
Rod-L Electronics M35 Ground Fault Tester 35 Amp Ground Continuity Test Instrument
Safe, Fast, Efficient
Performs ground continuity tests in full compliance with BSI, VDE and IEC
Test time is adjustable from 1 second to 90 seconds
Measures AC resistance from Chassis of Device Under Test (DUT) to po
http://www.kandelelex.com/jpegs/rdlm35.jpg in stock
Rod-L Electronics M500AVS5-1.5-350 AC Hipot Tester 0 - 1.5KV 0 - 350mA The M100/500 Series of AC Hipot Test Instruments is intended for production, receiving inspection and laboratory applications. Each instrument in the series performs safe and efficient testing, and in full compliance to UL, VDE, BSI, CSA, etc. test requir in stock
Rod-L Electronics M500AVS5-2.8-100 AC Hipot Tester 2.8kVAC 100ma Performs concurrent dielectric withstand and ground continuity test in a single operation, complying with U.L., C.S.A., I.E.C., V.D.E., and F.C.C. Test Voltage: 0 to 2.8kvac. Output Current: 100mA, adjustable trip point. http://www.kandelelex.com/jpegs/rdlm500avs5-2.8-100.jpg
Rod-L Electronics M500AVS5-5.0-100 AC Hipot Tester 0-5kVAC 0-100ma http://www.kandelelex.com/jpegs/rdlm500avs5-5.0-100.jpg
Rod-L Electronics M500AVS5-50-100 AC Hipot 100v-5kV 100ma http://www.kandelelex.com/jpegs/rdlm500avs5-50-100.jpg
Rod-L Electronics M500BVS5-28-200 AC Hipot 2.8kV 200ma Performs concurrent dielectric withstand and ground continuity test in a single operation, complying with UL, CSA, IEC, VDE, and FCC. Test Voltage: 0 to 2.8kvac. Output Current: 200mA, adjustable trip point. http://www.kandelelex.com/jpegs/rdlm500bvs5-28-200.jpg
Rod-L Electronics M500BVS5-50-100 AC Hipot 5kV 100ma Performs concurrent dielectric withstand and ground continuity test in a single operation, complying with UL, CSA, IEC, VDE, and FCC. Test Voltage: 0 to 5kvac. Output Current: 100mA, adjustable trip point. http://www.kandelelex.com/jpegs/rdlm500bvs5-50-100.jpg
Rohde & Schwarz AMIQ03 B2-B3-K11 The I/Q Modulation Generator AMIQ and the Simulation Software WinIQSIMT open up new dimensions for the generation of I/Q signals. The AMIQ is a dual-channel modulation generator that has consequently been designed for use as an I/Q source. It is progr
Rohde & Schwarz AMIQ03 K11 I/Q Modulation Generator he I/Q Modulation Generator AMIQ and the Simulation Software WinIQSIMT open up new dimensions for the generation of I/Q signals. The AMIQ is a dual-channel modulation generator that has consequently been designed for use as an I/Q source. It is progra in stock
Rohde & Schwarz AMIQ04 Waveform Generator 14-bit amplitude resolution; 4,000,000 samples memory depth; 100 MHz sample rate. Two signal outputs (I and Q). Integrated hard disk and floppy disk drive.
Rohde & Schwarz CMD55 B3-4-5-6-9-19-41-42-43-44-61-62 Communications Test Set Features of the Rohde & Schwarz CMD55 Digital Radiocommunication Tester:
Mobile Phone Tester for all GSM bands (GSM900/1800/1900)
Cost-effective solution for production lines
Extremely fast IEEE-bus operation for high production throughput
Versatile m
http://www.kandelelex.com/jpegs/r&scmd55 b3-4-5-6-9-19-41-42-43-44-61-62.jpg in stock
Rohde & Schwarz CMD80 Communications Test Set Supports: CDMA(800/1800/1900MHz bands), IS-136, AMPS, NAMPS, ETACS, NTACS, JTACS. Large LCD display. Cellular and PCS frequencies. Dual-mode CDMA/Analog measurements. Memory card interface. Options: B1,B3,B14,B60, B61,B81,B82,K2. http://www.kandelelex.com/jpegs/r&scmd80.jpg in stock
Rohde & Schwarz CMD80 B1-B3-B14-B60-B61-B62-B81-B82-B84-K1-K2 Communications Test Set Supports: CDMA(800/1800/1900MHz bands), IS-136, AMPS, NAMPS, ETACS, NTACS, JTACS. Large LCD display. Cellular and PCS frequencies. Dual-mode CDMA/Analog measurements. Memory card interface. Options: B1,B3,B14,B60, B61,B81,B82,K2. http://www.kandelelex.com/jpegs/r&scmd80 b1-b3-b14-b60-b61-b62-b81-b82-b84-k1-k2.jpg in stock
Rohde & Schwarz CMD80 B1-B3-B14-B60-B61-B62-B81-B82-K1-K2 Communications Test Set Supports: CDMA(800/1800/1900MHz bands), IS-136, AMPS, NAMPS, ETACS, NTACS, JTACS. Large LCD display. Cellular and PCS frequencies. Dual-mode CDMA/Analog measurements. Memory card interface. Options: B1,B3,B14,B60, B61,B81,B82,K2. in stock
Rohde & Schwarz EMFT TV Test Receiver The Rohde & Schwarz EMFT TV Test Receiver is a continuously tunable test receiver that features two isolated video outputs and two outputs for the Q signal. These outputs enable the measurement of incidental phase modulation of the vision carrier which in in stock
Rohde & Schwarz FSH6 Hand-Held Spectrum Analyzer with Preamplifier 100K The Rohde & Schwarz FSH6 is the ideal spectrum analyzer for rapid, high-precision, cost-effective signal investigations. It provides a large number of measurement functions to handle anything from the installation or maintenance of a mobile radio base sta in stock
Rohde & Schwarz FSU26 B10-B23-B25 Spectrum Analyzer 20Hz-26GHz The R&S FSU spectrum analyzers are performance leaders in dynamic range, phase noise, level accuracy, and resolution bandwidth - all factors that are essential for the user's ability to design, characterize, and manufacture next generation wireless elem http://www.kandelelex.com/jpegs/r&sfsu26 b10-b23-b25.jpg
Rohde & Schwarz FSU26 B18-B23-B25 Spectrum Analyzer 20 Hz - 26.5 GHz The R&S FSU spectrum analyzers are performance leaders in dynamic range, phase noise, level accuracy, and resolution bandwidth - all factors that are essential for the user's ability to design, characterize, and manufacture next generation wireless elem
Rohde & Schwarz FSU26 B4-B23-B25-K5-K7-K8-K30-K73-K83-K84 Spectrum Analyzer 20Hz-26GHz Frequency range 20 Hz to 26.5 GHz
Displayed average noise level -158 dBm (1 Hz)
Phase noise -123 dBc (1 Hz) at 10 kHz
TOI typ. +25 dBm
Resolution bandwidth 1 Hz to 50 MHz
Fast ACP in time domain
Up to 70 measurements per second (including trace
http://www.kandelelex.com/jpegs/r&sfsu26 b4-b23-b25-k5-k7-k8-k30-k73-k83-k84.jpg
Rohde & Schwarz FSU8 Spectrum Analyzer 20Hz - 8GHz http://www.kandelelex.com/jpegs/r&sfsu8.jpg
Rohde & Schwarz FSU8 B4-B25-K5-K8-K30-K73-K84 Spectrum Analyzer 20Hz - 8GHz Frequency range: 20 Hz to 8 GHz. Reference frequency aging: 1 x 10-7/year. Spectral purity: Phase noise typ. -123 dBc (1 Hz) at 10 kHz from carrier; Residual FM 1Hz. Sweep time: Span ≥10 Hz 2.5 ms to 16000 s; Span 0 Hz (zero span) 1 s to 16000 s. http://www.kandelelex.com/jpegs/r&sfsu8 b4-b25-k5-k8-k30-k73-k84.jpg
Rohde & Schwarz FSU8 K72-K73-K83 Spectrum Analyzer 20Hz - 8GHz Frequency range: 20 Hz to 8 GHz. Reference frequency aging: 1 x 10-7/year. Spectral purity: Phase noise typ. -123 dBc (1 Hz) at 10 kHz from carrier; Residual FM 1Hz. Sweep time: Span ≥10 Hz 2.5 ms to 16000 s; Span 0 Hz (zero span) 1 s to 16000 s. http://www.kandelelex.com/jpegs/r&sfsu8 k72-k73-k83.jpg
Rohde & Schwarz HK116 Biconical Dipole Antenna 20 - 300MHz HK116
Frequency range 20 to 300 MHz
Polarization linear
Nominal impedance 50 W
VSWR 2.5 typ.
Max. input power 20 W
Connector N female
Operating temperature -40 to +55C
Dimensions (L x W x H) 1380 mm x 530 mm x 720 mm
Weight 3 kg
http://www.kandelelex.com/jpegs/r&shk116.jpg
Rohde & Schwarz HL223 Log Periodic Antenna 200-1300MHz HL223
Frequency range 200 to 1300 MHz
Polarization linear
Nominal impedance 50 W
VSWR 2, typ. 1.6
Max. input power 1500 to 600 W CW
Gain >6 dBi
Connector N female
Max. wind speed 200 km/h (without ice deposit)
Dimensions (L x W) 710 m
Rohde & Schwarz NRP-Z11 Universal Power Meter-Sensor 10MHz-8GHz 200pW(-67d The R&SNRP-Z11 universal rf power sensor is, with a dynamic range of 90 dB for measurement of CW and modulated signals and a maximum power of +23 dBm, a very useful measurement instrument for a vast number of measurement tasks.

*True universal power
in stock
Rohde & Schwarz NRVZ5 Diode Sensor 100KHz-6GHz 10nw-500mw The Rohde & Schwarz NRV-Z5 is a medium-sensitivity sensor. Based on diode detectors with 20 dB attenuator, these sensors provide true RMS power measurement in the range from 10 nW to 1 mW and up to 500 mW for sinewave signals. Compared to thermocouple
Rohde & Schwarz NRVZ55 Thermocouple Power Sensor DC - 40GHz 1uw - 100mw Thermal power sensor 50 Ohm 0 - 40 GHz, 1 W - 100 mW K (2.92 mm) male, 1.3 m cable (p/n 1081.2005.02) in stock
Rohde & Schwarz SME03 Signal Generator 5KHz - 3GHz Frequency: 5KHz to 3GHz with .1Hz resolution. Output: -144 to +13(16dBm) with .1dB(.01)dB resolution and 1dB accuracy. SSB Phase Noise(@1GHz): -126dBc/Hz(20KHz offset). Features: sweep; GP-IB; 50W RF,35VDC overload protection; self diagnostics. Opt http://www.kandelelex.com/jpegs/r&ssme03.jpg in stock
Rohde & Schwarz SME03 B1-B4-B5-B8-B11-B12 Signal Generator 5KHz - 3GHz Frequency: 5KHz to 3GHz with .1Hz resolution. Output: -144 to +13(16dBm) with .1dB(.01)dB resolution and 1dB accuracy. SSB Phase Noise(@1GHz): -126dBc/Hz(20KHz offset). Features: sweep; GP-IB; 50W RF,35VDC overload protection; self diagnostics. Opt http://www.kandelelex.com/jpegs/r&ssme03 b1-b4-b5-b8-b11-b12.jpg in stock
Rohde & Schwarz SME06 Signal Generator 5KHz-6GHz Frequency: 5KHz to 6GHz with .1Hz resolution. Output: -144 to +13(16dBm) with .1dB(.01)dB resolution and 1dB accuracy. SSB Phase Noise(@1GHz): -126dBc/Hz(20KHz offset). Features: sweep; GP-IB; 50W RF,35VDC overload protection; self diagnostics. Opt http://www.kandelelex.com/jpegs/r&ssme06.jpg
Rohde & Schwarz SMG/B1/B2 Signal Generator/100KHz-1GHz/TCXO Frequency Range: 100KHz to 1000MHz with 1Hz resolution. Level: -137 to +13dBm(overrange +16dBm) with 0.1dB resolution. Spectral purity: harmonics;<-30dBc, <-140dBc broadband noise. Modulation: AM, FM(dc to 100KHz), FSK, PhM, and pulse. RF and AF(opt
Power Ten 4700P-25040 Power Supply 0-250v 0-40a 208 3ph
Power Ten 6101-4050 Power Supply 0 - 40V 0 - 50A 230VAC Switcher in stock
Power Ten I66C-60330 Programmable DC Power Supply 0-60V 0-330A GPIB Swi This series of programmable DC switching power supplies offers:
Low P_P Ripple and Noise 100mVp-p
Preset and Monitor of OVP Limit Set
IEEE 488.2 Remote programming
Regulation (line or load) 0.1%
190-253VAC 3ph input
Power Ten P63C-40166 DC Powr Supply 0-40V 0-166A 200-240VAC 3-Ph Switch The Power Ten (Ametek) P63 Series three phase supplies provide up to 10KW DC output and occupies only 5.25" vertical rack height(3U).
Output: 0 to 40 volts; 0 to 166 amps.
Output P-P Ripple: 75mV
Operates from Delta or Wye source
Input: 200-240VAC 3
in stock
Power Ten R63C-60166 Programmable DC Power Supply 0-60V 0-166A GPIB RS- The Power Ten R63 Series three phase supplies provide up to 10KW DC output and occupies only 5.25" vertical rack height(3U). This series is similar to the P63 series but has GPIB and RS-232 programmable interfaces.
Output: 0 to 60 volts; 0 to 166 amps.
in stock
PRD 1209-F1 WG Isolator 18-26GHz 24dB Isolation 10 Watt Ug599u
PRD 155-F1 WG K-Band Attenuator Variable 0 - 40dB in stock
PRD 413 WG Directional Coupler 12 - 18GHz 10dB in stock
PRD CX518 BroadBand Coaxial Frequency Meter Frequency range: 3.7 TO 12.4GHz direct reading. Accuracy: 0.17%. Type N connectors. 1 dB resonance dip. Similar to HP 537A. in stock
Precision Scientific THELCO 16 Electric Oven Gravity convection heated. Inside: 13" square. Outside: 26"H x 18"D x 18"W. 115VAC.
Princeton Applied Research (eg&g) 124 Lock-in Amplifier Accurately measures the amplitude and phase of weak signals buried in noise; 2Hz to 210KHz; sensitivity: 500V with 21 full scale ranges. I100M ohm SE/DE; 120dB at 60Hz; 1V sensitivity; 200VDC max input for 185 preamp. Preamps are available.
Princeton Applied Research (eg&g) 124A Lock-in Amplifier Accurately measures the amplitude and phase of weak signals buried in noise; 2Hz to 210KHz; sensitivity: 500V with 21 full scale ranges. Includes 116 or 117 differential preamp: 100M ohm SE/DE; 120dB at 60Hz; 1V sensitivity; 200VDC max input or 185 p http://www.kandelelex.com/jpegs/par124a.jpg
Quadtech 1433-10 Decade Resistor Box 1111.1 Ohm 5-Dial .01 ohm/ste The 1433 Decade Resistors are primarily intended for precision measurment applications where their excellent accuracy, stability, and low zero resistance are impotant.
The 1433-10 is equal to the General Radio 1433T.
This unit has 5-dials with .01 ohm/
in stock
Quadtech 1433-16 Decade Resistor Box 1.1111M Ohm 10 Ohm/step 5-Dial in stock
Quadtech 1692 Digibridge RLC Tester 100Hz - 100KHz .05% Accuracy The 1692 is a sophisticated, microprocessor-controlled tester that brings new levels of flexibility, simplicity and accuracy to RLC measurement. It's testing automation at its best with a range of programmable test frequencies and test voltages, as wel http://www.kandelelex.com/jpegs/qt1692.jpg in stock
Quadtech 1693 Precision RLC Digibridge
0.02% Accuracy for LCR, G Z and Y
0.0001 Accuracy for DQ measurements
Programmable test frequencies from 12Hz to 200kHz
Programmable test voltages from 5mV to 1.275V permits testing at exact manufacturer-specified voltage levels
Full range keybo
http://www.kandelelex.com/jpegs/qt1693.jpg
Quadtech 1710 Digibridge LCR Meter The Quadtech 1710 is a LCR Digibridge. The 1710 Digibridge makes primary measurements of L, C, and R and secondary measurements of D and Q. L, C & R measurements are made at a frequency of 120Hz or 1kHz with a basic accuracy of 0.2%. The accuracy of the
Quadtech 1730 Precision LCR Meter 50Hz - 100KHz The QuadTech 1730 can measure and display two of 14 impedance parameters simultaneously with a basic accuracy of 0.1%. Test results can also be shown as Deviation or %Deviation from nominal value. 10 Test Frequencies: User selectable: 50Hz, 60Hz, 100H http://www.kandelelex.com/jpegs/qt1730.jpg
Quadtech 1865 Digital Megohmmeter / IR Tester The QuadTech 1865 is a Megohmmeter and Insulation Resistance tester combined in one unit. Features; basic measurement accuracy of 0.5%, voltage range from 1V to 1000V DC in 2 ranges with 25mV resolution and 1% accuracy, measurement range from 1k ohm to http://www.kandelelex.com/jpegs/qt1865 01.jpg
Quadtech 1865 01 Programmable Megohmmeter-IR Tester 1-1000V GPIB The QuadTech 1865 is a Megohmmeter and Insulation Resistance tester combined in one unit. Features; basic measurement accuracy of 0.5%, voltage range from 1V to 1000V DC in 2 ranges with 25mV resolution and 1% accuracy, measurement range from 1k ohm to
Quadtech 1865 01-02 Digital Megohmmeter / IR Tester Megohmmeter and Insulation Resistance tester combined in one unit. Features; basic measurement accuracy of 0.5%, voltage range from 1V to 1000V DC in 2 ranges with 25mV resolution and 1% accuracy, measurement range from 1k ohm to 100T ohm in 7 ranges, http://www.kandelelex.com/jpegs/qt1865 01-02.jpg
Quadtech 1865 01-02-CE Digital Megohmmeter/IR Tester Megohmmeter and Insulation Resistance tester combined in one unit. Features; basic measurement accuracy of 0.5%, voltage range from 1V to 1000V DC in 2 ranges with 25mV resolution and 1% accuracy, measurement range from 1k ohm to 100T ohm in 7 ranges, http://www.kandelelex.com/jpegs/qt1865 01-02-ce.jpg
Quadtech 1880 Milliohmmeter 2 Mohms Down To 1 ohm The Quadtech 1880 Milliohmmeter provides ease of use, digital display and excellent accuracy for performing low resistance measurements on switches, relays, connectors and a variety of other devices. The instrument offers a wide measurement range, from http://www.kandelelex.com/jpegs/qt1880.jpg in stock
Quadtech 1880 01 Milliohmmeter 2 Mohms Down to 1 ohm The Quadtech 1880 Milliohmmeter provides ease of use, digital display and excellent accuracy for performing low resistance measurements on switches, relays, connectors and a variety of other devices. The instrument offers a wide measurement range, from http://www.kandelelex.com/jpegs/qt1880 01.jpg
Quadtech 1910 Inductance Analyzer Features

 Measures 15 Impedance Parameters, DC Resistance, Voltage and Current
 0.1% Basic Measurement Accuracy
 27,000 Programmable Frequencies from 20Hz to 1MHz
 AC Test Voltage Programmable from 20mV to 1V
 Internal DC Bias Current, Pr
Quadtech 2520 Guardian AC/DC Hipot Tester 5KVAC / 6kVDC 15mA AC The Guardian 2500 Series builds upon QuadTechs Sentry family of electrical safety testers and incorporates a unique Ground Fault Interruption (GFI) feature as well as an RS232 interface and optional IEEE488 or enhanced remote interfaces. The GFI circuit in stock
Quadtech 2530 40 Gardian AC-DC-IR Hipot Tester 5KVAC 15mA 6KVDC 7.5 The Gardian series hipot tester is designed to perform the most common electrical safety tests outlined in UL, TUV, IEC and other standards.
Features:
*Programmable Output Voltage to 5KVAC and 6KVDC.
*Output Current: 1uA to 15mAAC; .1uA to 7.5mADC
*Gr
in stock
Quadtech 6000 Electrical Safety Analyzer 5KVAC 6KVDC 50Gohm 30A The Guardian 6000 Electrical Safety Analyzer performs AC and DC hipot (hy-pot), insulation resistance, ground bond (continuity) and leakage current measurements for a complete dielectric testing solution. A fully automated tester, the 6000 performs both h in stock
Quadtech 7000-05 Chip Component Tweezers Accessory for 1689M-7400- Chip component tweezers to 4 BNC, (1 meter in length) for handling and measuring surface mount devices (mdD) on the 74/7600. Maximum component size 14mm. in stock
Quadtech 7400 Precision RLC Meter 10Hz - 500KHz Measure and display any two of 14 parameters simultaneously. Measurement frequency: 10Hz to 500KHz with 229,900 programmable frequencies. Graphical and tabular display of swept frequency, voltage and current measurements with 7-digit resolution. 0.05 http://www.kandelelex.com/jpegs/qt7400.jpg in stock
Quadtech 7600 Precision LCR Meter 10Hz-2MHz .05% The Quadtech 7600 LCR Meter is designed to perform precision impedance measurements over a wide frequency range, 10 Hz to 2 MHz. The instrument is capable of measuring 14 different parameters with 0.05% accuracy to meet today's requirements for compone http://www.kandelelex.com/jpegs/qt7600.jpg in stock
Quadtech 7600A CE Precicion LCR Meter with 500V Ext Bias CE Marked The Quadtech 7600 LCR Meter is designed to perform precision impedance measurements over a wide frequency range, 10 Hz to 2 MHz. The instrument is capable of measuring 14 different parameters with 0.05% accuracy to meet today's requirements for compone
Quadtech GUARDIAN 5000 AC-DC-IR-GC Safety Analyzer (Hipot) .1-5KVAC .5-6K The Quadtech Guardian 5000 Electrical Safety Analyzer is four instruments in one, providing AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond measurements from a single test connector in one versatile instrument. This provides a cost effective so in stock
Quadtech GUARDIAN II AC/DC Hipot Tester 100V - 5KVAC / 6kVDC AC and DC hipot testing in one instrument with GPIB and user friendly menu driven interface. Output Voltage: 100V to 5KVAC(60Hz) and 100V to 6KVDC(+ grounded) with 3% setting accuracy and 10V steps. Leakage Current: 0 to 10mA AC, 10uA/step and 0 to 5 http://www.kandelelex.com/jpegs/qtguardian ii.jpg in stock
Quadtech LR2000 Milliohmmeter 1μΩ - 2MΩ 0.05% Accuracy The LR2000 Milliohmmeter with its LCD display and menu-type front
panel programming assures that low resistance measurements on switches,
relays, cables, and other devices can be made quickly and easily. With a
basic accuracy of 0.05% the instrument of
Quadtech SENTRY 10 PLUS AC Hipot Tester 50V to 5KVAC 1uA to 20mA Description
The Sentry 10 Plus AC Hipot Tester (CE Mark) performs AC dielectric withstand (hipot) tests. The test voltage is programmable from 50V to 5kV AC with a resolution of 1V. The current range is 1A to 20mA.
Program & Display Ground Continuity
Quadtech SENTRY 30 AC/DC/IR Hipot Tester .1MΩ-50GΩ 50-5KVDC@5mA 50-6K The Sentry 30 Plus AC/DC/IR Hipot Tester (CE Mark) has all of the features of the Sentry 20 Plus in addition to Insulation Resistance (IR) testing. The IR measurement range is from 0.1MΩ to 50GΩ with test voltages from 50 to 1000VDC.
Program & Display Gr
in stock
Quadtech SENTRY10 AC Hipot Tester 0-5kVAC 20ma The Sentry 10 AC Hipot Tester (CE Mark) performs AC dielectric withstand (hipot) tests. The test voltage is programmable from 50V to 5kV AC with a resolution of 1V. The current range is 1A to 20mA. http://www.kandelelex.com/jpegs/qtsentry10.jpg
Quantum Data 801A Video Character Generator Programmable RGB video test generator for servicing color monitors. 16 Selectable color patterns. Programmable dot clock range of 1.024-32.768MHz color, 65.520MHz monochrome.
Racal Dana 1260-12 20-Channel DPDT 220V 2A Switch Card in stock
Racal Dana 1260-13 40-channel Dpst220v 2A Switch Card
Racal Dana 1260-35A 2-Wire 1 x 96 Multiplexer Card in stock
Racal Dana 1261E VXI Mainframe in stock
Racal Dana 1992 Universal Frequency Counter DC - 1.3GHz Half-rack unit features 9-digit resolution in 1 second. Channel A: 0 to 160MHz with 25mV sensitivity up to 100MHz(50mV to 160MHz). Channel C: 40MHz to 1.3GHz with 10mV sensitivity up to 1GHz(75mV to 1.3GHz). GP-IB available.
Racal Dana 9087 Synthesized Signal Generator 10KHz - 1300MHz http://www.kandelelex.com/jpegs/rac9087.jpg in stock
Radio Frequency Labs 440 Magnet Treater
Radio Frequency Labs 912 Gauss Meter And Probe Where high sensitivity and wide measurement range are required. Includes 7199 probe.
Ransco Environmental 925 Hot / Cold Temperature Chamber Temperature range: -73 to +273C; Dimensions: Inside; 10.5D x 14.5"W x 8.75"H; Exterior; 21"H x 19"D x 19"W, rack mount unit. CO2 or LN2 cooling. Forced draft. Stainless steel interior. Single set point controller with digital readout of temperature
Raytheon 370708 Shielded Room Leak Detector Portable system includes a transmitter, receiver, articulated receiver probe, probe extension, and transmitter cable set housed in a transit case. Transmitter: 95KHz (crystal controlled); 16 watts peak, high range, 1.6 watts peak, low range. Modulated in stock
Reichert Jung (Leica) 312508 Photographic Microscope This is a trinocular head microscope with base light. We will try to answer your questions reguarding this unit. http://www.kandelelex.com/jpegs/rei312508.jpg in stock
Reichert Jung (Leica) 569B Stereo Star Zoom Microscope Magnification: .7 to 3X. Similar to B & L StereoZoom 4. http://www.kandelelex.com/jpegs/rei569b.jpg in stock
Research Devices D Infrared Microscope System includes 20X and 6X lenses mounted on a 4-turrett base with infrared light source and a standard light source. Eyepeices and power supplies are missing. in stock
Research Devices NC-67X Camera And Power Supply BNC video and vertical sync connectors. in stock
RF Industries RFA-4013 7/16 DIN Adapter Kit in stock
Riser Bond 1205TX-OSP Metallic TDR Cable Fault Locator Dual Input, Combination Short/Long Range Metallic Time Domain Reflectometer Cable Fault Locator Optimized for Loaded Cable Systems. Test loaded cables up to 80 miles - 130 km! Two line, live input for cable comparison. Automatic crosstalk measurement http://www.kandelelex.com/jpegs/rb1205tx-osp.jpg
Riser Bond 1270 TDR Metallic Time Domain Reflectometer Cable Fault Metallic Time Domain Reflectometer Cable Fault Locator. The ultimate combination TDR for testing both twisted pair and coaxial cables.
Using Model 1270A results in superior fault location in any industry and any application.
Sub-nanosecond pulse w
http://www.kandelelex.com/jpegs/rb1270.jpg
Riser Bond 1550 Metallic Time Domain Reflectometer Cable Fault Loc Metallic Time Domain Reflectometer Cable Fault Locator
The Riser Bond 1550 is an easy to use handheld entry level TDR. It is optimized to help the field engineer find the most common first line faults, the Riser Bond 1550 can be used across a broad range
in stock
Rod-L Electronics M100AVS5-1.5-50 AC Hipot Tester 1.5kV 50mA Performs concurrent dielectric withstand and ground continuity test in a single operation, complying with UL, CSA, IEC, VDE, and FCC Test Voltage: 0 to 1.5kvac. Output Current: 50mA, adjustable trip point. http://www.kandelelex.com/jpegs/rdlm100avs5-1.5-50.jpg in stock
Rod-L Electronics M100AVS5-1-10 Hipot 1KV 10mA in stock
Rod-L Electronics M100AVS5-2.8-40 Hipot Tester Performs concurrent dielectric withstand and ground continuity test in a single operation, complying with UL, CSA, IEC, VDE, and FCC. Test Voltage: 0 to 2.8kvac. Output Current: 40mA, adjustable trip point. http://www.kandelelex.com/jpegs/rdlm100avs5-2.8-40.jpg in stock
Rod-L Electronics M100AVS5-50-25 AC Hipot Tester 5kV 25ma Performs concurrent dielectric withstand and ground continuity test
in a single operation, complying with UL, CSA, IEC, VDE, and F.C.C. Test Voltage: 0 to 5.0kVAC. Output Current: 25mA, adjustable trip point.
http://www.kandelelex.com/jpegs/rdlm100avs5-50-25.jpg
Rod-L Electronics M100BVS5-2.8-40 Hipot Tester Performs concurrent dielectric withstand and ground continuity test in a single operation, complying with UL, CSA, IEC, VDE, and FCC. Test Voltage: 0 to 2.8kvac. Output Current: 40mA, adjustable trip point. "BV" models have Real(Resistive) Current me http://www.kandelelex.com/jpegs/rdlm100bvs5-2.8-40.jpg in stock
Rod-L Electronics M100BVS5-5.0-25 AC Hipot 0 - 5KV 0 - 25mA All ROD-L hipot testers have adjustable electronically controlled test voltage ramp control and timing circuits. In addition, ROD-L AC and DC hipot testers interconnect to simplify multiple testing requirements. Each are compatible with all ROD-L Ground C in stock
Rod-L Electronics M100DC-5.5-100 Hipot Tester 0 - 5.5kVDC 0 - 100ma http://www.kandelelex.com/jpegs/rdlm100dc-5.5-100.jpg in stock
Rohde & Schwarz SMHU52 Synthesised Signal Generator 100KHz - 4.32GHz Features:
Extremely high spectral purity
Frequency setting time <1 ms
Frequency resolution 0.1 Hz
RF, AF, level and memory sweeps
Broadband FM from DC to 1 MHz
Frequency-accurate and drift-free FM DC for FSK applications
OCXO as a reference
http://www.kandelelex.com/jpegs/r&ssmhu52.jpg in stock
Rohde & Schwarz SMHU56 RF Signal Generator 100KHz - 4320MHz +19dBm Outpu The SMHU56 Signal Generator can generate complex test signals for modern communications and radar systems. Its high versatility is based upon the great variety of modulation capabilities in conjunction with high spectral purity and frequency hopping.
http://www.kandelelex.com/jpegs/r&ssmhu56.jpg in stock
Rohde & Schwarz SMHU58 RF Signal Generator 100KHz - 4320MHz +19dBm Outpu The SMHU58 Signal Generator can generate complex test signals for modern communications and radar systems. Its high versatility is based upon the great variety of modulation capabilities in conjunction with high spectral purity and frequency hopping.
http://www.kandelelex.com/jpegs/r&ssmhu58.jpg in stock
Rohde & Schwarz SMIQ03 Vector Signal Generator 300 KHz To 3.3 GHz 0.3 GHz to 3.3 GHz, 0.1 Hz resolution
Versatile and Broadband Generation of Digitally Modulated Signals up to 7 Msymbol/s
Analog and Digital Modulation Capabilities
Generation of TDMA and CDMA Signals to all Main Mobile Radio Standards
Broadband I
http://www.kandelelex.com/jpegs/r&ssmiq03.jpg
Rohde & Schwarz SMIQ03 B50 Vector Signal Generator 300KHz - 3.3GHz 0.3 GHz to 3.3 GHz, 0.1 Hz resolution
Versatile and Broadband Generation of Digitally Modulated Signals up to 7 Msymbol/s
Analog and Digital Modulation Capabilities
Generation of TDMA and CDMA Signals to all Main Mobile Radio Standards
Broadband I
http://www.kandelelex.com/jpegs/r&ssmiq03 b50.jpg in stock
Rohde & Schwarz SMIQ03B Vector Signal Generator 300KHz - 3.3GHz The Rohde & Schwarz SMIQ03B Signal Generator offers solutions for today and tomorrow. Frequency Range: 300KHz to 3.3GHz with .1Hz resolution and <1x100(-6)/year accuracy. Output: -144dBm to +13dBm with 0.1 and .01dB resolution and <.9dB uncertainty. http://www.kandelelex.com/jpegs/r&ssmiq03b.jpg in stock
Rohde & Schwarz SMIQ03B B1-B11-B12-B14-B17-B20 Vector Signal Generator 300KHz-3.3GHz The Rohde & Schwarz SMIQ03B Signal Generator offers solutions for today and tomorrow. Frequency Range: 300KHz to 3.3GHz with .1Hz resolution and <1x10(-9)/day
accuracy(opt.B1). Output: -144dBm to +13dBm with 0.1 and .01dB resolution and <.9dB uncerta
http://www.kandelelex.com/jpegs/r&ssmiq03b b1-b11-b12-b14-b17-b20.jpg
Rohde & Schwarz SMIQ03E B10-B11 Vector Signal Generator 300KHz - 3.3GHz The economy models SMIQ02E and SMIQ03E have especially been designed for the needs in production, environments and satisfy the requirement for an economically attractive solution with an outstanding price/performance ratio.
Main features
 Versatile a
http://www.kandelelex.com/jpegs/r&ssmiq03e b10-b11.jpg in stock
Rohde & Schwarz SMP02 Microwave Signal Generator 2-20GHz The Microwave Signal Generator R&S SMP is a reliable, high-precision signal source featuring high output power, high spectral purity and excellent pulse modulation. It is able to supply different modulations for any measurement on radar and communicati http://www.kandelelex.com/jpegs/r&ssmp02.jpg
Rohde & Schwarz SMP04 B1-B2-B5-B11-B12-B13-B14 Microwave Signal Generator 10MHz - 40GHz The Microwave Signal Generator R&S SMP is a reliable, high-precision signal source featuring high output power, high spectral purity and excellent pulse modulation. It is able to supply different modulations for any measurement on radar and communication
Rohde & Schwarz SMU200A B10-13-103-203-K11-12-17-40-42-43-61 Vector Signal Generator Specifications:
Frequency range: 100 kHz to 3GHz. Setting time <3 ms. Setting time in List mode <450 s. Level Range -145 dBm to +13 dBm (PEP, 3 GHz). Range with high-power output option -145 dBm to +19 dBm (PEP, 3 GHz). Spectral purity (at f = 1
Rohde & Schwarz SMY02 Signal Generator 9 KHz To 2.08 GHz The SMY02 Signal Generator is a cost-effective instrument for testing AM, FM, and ΦM receivers and for component measurements.
Frequency Range 9 kHz to 2.08 GHz
Frequency Resolution 1 Hz
Level Range -140 to +13 dBm, Over Range up to 19 dBm
Level
http://www.kandelelex.com/jpegs/r&ssmy02.jpg in stock
Rohde & Schwarz UAF Video Analyzer The Rohde & Schwarz UAF signal analysis comprises 25 video and test line parameters and covers all important levels as well as linear and nonlinear distortions such as 2T K rating, frequency response and hum. The position of the test lines can be freel http://www.kandelelex.com/jpegs/r&suaf.jpg
Rohde & Schwarz URV5 RF DC Millivoltmeter Power Meter 2-Channel Millivoltmeter URV5 is a broadband voltage, level and power meter of high accuracy and sensitivity. It is suitable both for manual operation and for use in systems. A wide choice of individually calibrated probes and sensors allows URV5 to be used for http://www.kandelelex.com/jpegs/r&surv5.jpg in stock
Rohde & Schwarz ZVC62 B2-B4-B5-B7-K9-B16 8GHz Network Analyzer The Rohde & Schwarz, Inc. ZVC62 network analyzer is an instrument which measures the complex transmission and reflection characteristics of two-port devices in the frequency domain. It does this by sampling the incident signal, separating the transmitted
Roto Form Mfg Corp 151 Roto II Lead Former And Cutter The Roto IIr, Model 151 Axial Component Former combines the time proven tape fed design with a non-jamming mechanized "walking beam" Loose Parts Feeder to give you the best of both techniques in one economical machine. You can leave both feeders mounte in stock
Roto Form Mfg Corp 172 Roto-trim Circuit Board Lead Trimmer This machine has a variable speed cutting blade and is manually operated. The board is held in place by clamps on the platform.
Sage 930A Service Monitor The Sage 930A is a used Combination Test Set that is designed to meet all of the applications associated with testing Network Switching and DS1 Facilities. The standard Sage 930A is a high performance Signaling, TIMS and Return Loss Measuring Set with in stock
Saunders & Associates 100HF Crystal Impedance Meter Line test crystal oscillator; 1 to 60MHz. in stock
Schaffner NSG2025-3 Fast Transient Burst Generator 4.4kV 1MHz 30A 1-Ph The Schaffner NSG 2025 is a high end burst generator and the choice for users who need the maximum in pulse amplitude/frequency capabilities, flexibility, coupling network features and EUT connectivity. Based on a 'buildingblock' concept, the Schaffne http://www.kandelelex.com/jpegs/sfrnsg2025-3.jpg
Schaffner NSG-203A AC Voltage Variation And Dropout Plug-in Used in NSG-200 mainframe.. Simulates complete power interrupts and brownouts.
Schaffner NSG-431 E.S.D. Simulator Test electrostatic charging between person and machine. Discharge voltage: 2 to 21KV. Repetition Frequency: approx. 20Hz. Positive polarity, single or continuous mode of operation. http://www.kandelelex.com/jpegs/sfrnsg-431.jpg in stock
Schaffner NSG433 Electrostatic Discharge Simulator System Discharge Voltage (air): 2 - 18 kV
Discharge Voltage (contact): 2 - 9 kV
Polarity: Positive or negative (switchable)
Operating Modes: Single or repetitive discharge
Test Finger: Conforms to IEC 801-2
Max Discharge Energy: 47 mj
Rise Time (air)
Schlumberger 1250 Frequency Response Analyzer Frequency Range: 10uHz to 65KHz. True "Single Sine" measurement technique for precise gain-phase measurements in servo-loop applications. Amplitude Range: 10mV to 10.23 volts. Two independent channels. IEEE-488 Interface. http://www.kandelelex.com/jpegs/sch1250.jpg in stock
Schlumberger 1253 Gain-Phase Analyzer The 1253 Frequency Response Analyzer (FRA) is an instrument that is capable of meeting today's measurement requirements for dynamic system analysis. Using the single Sine Correlation technique (SSC), it provides precise data relating to the gain and ph http://www.kandelelex.com/jpegs/sch1253.jpg
Schlumberger 35301D Input Connector in stock
Schlumberger 35304A Input Module in stock
Schlumberger 3530D Data Logger Can handle up to 600 inputs, can run 8 different prioritized tasks, output results in engineering units and communicate over RS232C or GP-IB interfaces. Provides easy programming from the front panel keyboard and menu display. Has built-in thermal pri in stock
Scientific Atlanta 11-0.9 WG to Coaxial Adapter 0.9 - 1.15GHz in stock
Scientific Atlanta 11-1.7 WG To Coax Adapter 1.7-2.6GHz N
Scientific Atlanta 11-12.4 WG to Coaxial Adapter 12 - 18GHz in stock
Scientific Atlanta 11-2.6 Wageguide to Coax Adapter Used with 12-2.6 in stock
Scientific Atlanta 11A-3.9 WG To Coax Adapter 3.9-5.8GHz
Scientific Atlanta 11A-5.8 WG To Coax Adapter 5.8-7.0GHz
Scientific Atlanta 12-0.9 Horn Antenna .95 To 1.15GHz
Scientific Atlanta 12-1.7 Standard Gain Horn 1.7-2.6GHz
Scientific Atlanta 12-12 Waveguide Horn Antenna Frequency range: 12.4 to 18 GHz. UG-419 flange.
Scientific Atlanta 12-2.6 Standard Gain Horn (2.6-3.95GHz) in stock
Scientific Atlanta 12-26 Standard Gain Horn ( 26 - 40GHz Round Flange ) in stock
Scientific Atlanta 12-5.8 Standard Gain Horn (5.8-8.2GHz) http://www.kandelelex.com/jpegs/s-a12-5.8.jpg
Scientific Atlanta 12-60 Waveguide Horn 60 - 90GHz
Scientific Atlanta 12F-1.7 Mount for 12 - 1.7 Standard Gain Horn in stock
Scientific Atlanta 1743 Low Frequency Converter .1 - 2GHz in stock
Scientific Atlanta 1752 Wide Range Phase / Amplitude Receiving System in stock
Scientific Atlanta 1823A-1 Digital Phase Display Used with 1750 and 1770 receivers. Phase is displayed as +180 or 0 to 360 scale with 0.1 resolution.
Scientific Atlanta 1833A-20-1-2 Ratiometer Dual channel unit has 2)1830-1 preamp / display modules.
Scientific Atlanta 4423-252 Position Indicator Rack mount unit has three panel meters measure upper and lower Azimuth and elevation. in stock
Servo Corp. 2130 TWT Amplifier 4 - 8GHz 10 Watt TWT amplifier provides a minimum of 10 watts output, 30dB gain with a frequency range from 4 to 8GHz.
Servo Corp. 2210 TWT Amplifier 1-2GHz 10 Watt
Servo Corp. 2230 TWT Amplifier
Sierra/philco/lear Sieglers 160B150 RF Termination 150 Watt DC-5GHz N(f)
Sigma Systems M170 Tempature Chamber Co2 The M170 is a Cryogenically cooled (L-CO2 or LN2) chamber. Supplied with hinged lift off door. Model C4 programmable controller is standard with the M170. Chamber Size: Workspace Volume: 5.8 cubic feet (165 cubic liters); 25.1"H x 20.5"W x 19.6"D(63.
Singer Metrics A1-58-20 High Power Coaxial Attenuator 20dB DC to 2GHz; 20dB; 25watt. in stock
Slaughter 103/105MP-10 AC/DC Insulation Tester Voltage: 0 to 5KV AC/DC. Current: 0 to 5mA in 3 ranges. Audio and visual alarms. Capacity compensation. Auto testing with timer.
Slaughter 103/105MP-2.5 AC / DC Hipot Tester Voltage: 0 to 2.5KV AC/DC. Current: 0 to 5mA in 3 ranges. Audio and visual alarms. Capacity compensation. Auto testing with timer.
Slaughter 103-105-2.5 AC DC Hipot Tester 0-2.5KV AC & DC
Solar 6220-1A Audio Isolation Transformer 30Hz-250KHz 100 Watts The Type 6220-1A Audio Isolation Transformer was especially designed for screen room use in making conducted audio frequency susceptibility tests as required by MIL-STD-461/462 and other EMI specifications.
SPECIFICATIONS
Primary: Less than 5 ohms.
Sec
Solar 6254-5 Transient Generator Designed for screen room use in making conducted transient susceptibility tests. Provides 10V up to 250V peak with less than 0.5us rise time, falling to zero in 10us.
Solar 6338-57-TS-50N Line Impedance Stabilization Network Single line LISN, 50 amps, 57uH, 14KHz-4MHz; line/ground 270V@50/60Hz, 130V@400Hz. MIL-STD-462, V.D.E., CISPR, C22.4, NACSEM5100, ANSI C63.2.
Solar 6512-106R Feed Thru Capacitor 10 mfd 600VDC 275Vrms 60Hz 250 The Type 6512-106R Feed-Thru Capacitor was especially designed
for use in RFI/EMI test setups as required by MIL-STD-461/462 and other specifications. In this application it provides a low r.f. impedance across the power source so that EMI currents prod
Solar 6516-57-TS-10-BNC LISN 10 amps; 57uH; 150KHz to 65MHz; Line/Ground Voltage: 270V at 50/60Hz, 130V at 400Hz. in stock
Solar 6741-1 RF Current Probe 10KHz-100MHz The Solar 6741-1 is a monitoring current probe. It has a 1.25"(32mm) window size. The nominal transfer impedance is 0.7 ohms from 10KHz to 100MHz.
Solar 7054-1A Spike Generator 400 Volts Peak The Solar 7054-1A was especially designed for screen room use in applying high voltage transients at power line inputs to electronic equipment. The adjustable amplitude make it possible to determine the threshold of susceptibility to spikes appearing on t
Solar 7225-1 Line Impedance Stabilization Network LISN 10A 650u This LISN uses a series inductor between the test sample and the power source to provide the impedance-versus-frequency characteristic. A BNC coaxial connector with DC isolation is provided for connection to the associated frequency selective EMI meter. T
Solar 8012-50-R-24-BNC Line Impedance Stabilization Network LISN The Solar 8012-50-R-24-BNC L.I.S.N. is a dual line input unit. Amps: 50. uH:100. Frequency: 10KHz-50MHz. Line/Ground Voltage: 135(50-60Hz) 120(400Hz. Case size: 4.5"w x 4.5"h x 9.25".
Solar 8028-50-TS-24-BNC Line Impedance Stabilization Network Single line, 50uH LISN (10KHz-30MHz)rated at 270v, 50-400Hz, up to 24 amps in stock
Solar 9108-1N Bulk Current Injection Probe 10KHz-200MHz 10 Amps The principal use of the bulk current injection probe is for inducing RF current into the signal and power cables of equipment under test to determine conducted RF susceptibility. The injection prrobe can also be used as a sensor. The Solar 9108-1N featur
Solar 9117-5-PJ-50-N Line Impedance Stabilization Network 50A 5uH 240V Solar 9117-5-PJ-50-N 50A 5uH 500V Line-Ground 240V Single Circuit
150 kHz -1 GHz
in stock
Solar 9120-1N Bulk Current Injection Probe 4MHz-1GHz 30 Amps 50 The principal use of the bulk current injection probe is for inducing RF current into the signal and power cables of equipment under test to determine conducted RF susceptibility. The injection prrobe can also be used as a sensor. The Solar 9120-1N featur in stock
Solar 9230-1 9229-1 Radiating Loop & Loop Sensor Test Method RS101 of MIL-STD-461D requires radiated magnetic fields over the frequency range 30 Hz to 100 KHz to determine the susceptibility or immunity of the equipment under test (EUT). Two loop antennas are required for compliance with the requirement
Solar 9330-1 Calibration Fixture in stock
Solar 9924-5-TS-100-N Line Impedance Stabilization Network (ISO 7637-2) in stock
Sorensen 488-DAP Digital-to-Analog Programmer Allows any programmable power supply (ie; Sorensen DCR-series) to interface with GP-IB. Single output, dual output (V & I control).
Sorensen 488UDAP Digital-to-Analog Programmer Allows any programmable power supply (ie; Sorensen DCR-series) to interface with GP-IB. Single output, dual output (V & I control).
Sorensen DCR10-170B Power Supply 0-10v 0-170A 220 VAC
Sorensen DCR10-80B Power Supply 0 - 10V 0 - 80A 120VAC
Sorensen DCR110-45T Power Supply 0 - 110V 0 - 45A 208VAC 3-Phase in stock
Sorensen DCR150-12B Power Supply 0-150v 0-12A 103-127VAC
Sorensen DCR150-12B2 Power Supply 0 - 150V 0 - 12A 103 - 127VAC
Sorensen DCR150-18B Power Supply 0-150v 0-18a 187-229VAC in stock
Sorensen DCR150-35A Power Supply 0-150v 0-35a 3ph In
Input Voltage Range:187-229, 207-253\
Input Frequency: 50-63 Hz
Input Max Current: 35 A at 230 Vac
Efficiency: 77% typical
Output Voltage:0-150
Output Fine adjustment Range: 7.5 Vdc
Output Current Range: 0-35 A
Output Voltage Regulation: 0.10% or
Sorensen DCR150-3B Power Supply 0 - 150V 0 - 3A in stock
Sorensen DCR150-5A Power Supply 0 - 150V 0 - 5A
Sorensen DCR150-6B Power Supply 0-150v 0-6a
Sorensen DCR150-70A Power Supply 0-150v 0-70A 3ph
Sorensen DCR16-310T Power Supply 0-16v 0-310a 3ph
Sorensen DCR20-1000A Power Supply 0-20v 0-1000a 480 VAC 3ph
Sorensen DCR20-115B Power Supply 0 - 20V 0 - 115A
Sorensen DCR20-250A Power Supply 0-20v 0-250a 208VAC 3ph
Sorensen DCR20-25B Power Supply 0 - 20V 0 - 25A http://www.kandelelex.com/jpegs/sordcr20-25b.jpg in stock
Sorensen DCR20-25B2 Power Supply 0-20v 0-25a
Sorensen DCR20-500A Power Supply 0-20v 0-500a 3ph
Sorensen DCR20-50B Power Supply 0-20v 0-50a
Sorensen DCR20-50B2 Power Supply 0 - 20V 0 - 50A in stock
Sorensen DCR300-1.5B Power Supply 0 - 300V 0 - 1.5A http://www.kandelelex.com/jpegs/sordcr300-1.5b.jpg
Sorensen DCR300-16T Power Supply 0-300v 0-16a
Sorensen DCR300-18A Power Supply 0-300v 0-18a 208VAC 3ph
Sorensen DCR300-33T Power Supply 0-300v 0-33a 208VAC 3ph
Sorensen DCR300-35A Power Supply 0-300v 0-35a 208VAC 3ph
Sorensen DCR300-3B Power Supply 0 - 300V 0 - 3A
Sorensen DCR300-6B Power Supply 0-300v 0-6a 220 VAC
Sorensen DCR300-9B Power Supply 0 - 300V 0 - 9A 220 VAC
Sorensen DCR300-9B M50 Power Supply 0-300v 0-9A 220 VAC Digital Meters
Sorensen DCR300-9B2 Power Supply 0-300v 0-9A
Sorensen DCR32-155T Power Supply 0-32v 0-155a 220 VAC 3ph
Sorensen DCR32-310T5 Power Supply 0-32v 0-310a 480 VAC 3ph
Sorensen DCR40-125A Power Supply 0-40v 0-125a 208VAC 3ph
Sorensen DCR40-13B Power Supply 0 - 40V 0 - 13A in stock
Sorensen DCR40-13B2 Power Supply 0 - 40V 0 - 13A Over-Voltage Output Voltage: 0-40 Vdc
Output Current: 0-13 Amp
Regulation: 12 mV
RMS Ripple 90 mV max
Noise P-P 120 mV max
Transient Response time: 50 ms
in stock
Sorensen DCR40-250A Power Supply 0-40v 0-250a 460 VAC 3ph These are NEW units, while supply lasts.
Sorensen DCR40-25B Power Supply 0 - 40V 0 - 25A in stock
Sorensen DCR40-25B2 DC Power Supply 0-40v 0-25a
Sorensen DCR40-40B Power Supply 0 - 40V 0 - 40A in stock
Sorensen DCR40-40B2 Power Supply 0 - 40V 0 - 40A 120VAC in stock
Sorensen DCR40-500A Power Supply 0-40v 0-500a 380-460 VAC 3ph
Sorensen DCR40-60A Power Supply 0-40v 0-60a 220 VAC
Sorensen DCR40-70B Power Supply 0-40v 0-70A 220 VAC in stock
Sorensen DCR40-70B2 Power Supply 0-40v 0-70A Ov Protection 208VAC
Sorensen DCR600-.75B Power Supply 0 - 600V 0 - .75A
Sorensen DCR600-.75B2 Power Supply 0 - 600V 0 - .75A http://www.kandelelex.com/jpegs/sordcr600-.75b2.jpg in stock
Sorensen DCR600-1.5B Power Supply 0 - 600V 0 - 1.5A
Sorensen DCR600-16T Power Supply 0-600V/0-16A 220 VAC 3ph
Sorensen DCR600-18A Power Supply 0 - 600V 0 - 18A 3-Phase 208 / 460V "DON'T SELL"
Sorensen DCR600-3B Power Supply 0-600v 0-3a in stock
Sorensen DCR600-3B2 Power Supply 0 - 600V 0 - 3A Over-Voltage
Sorensen DCR600-4.5B2 Power Supply 0-600v 0-4.5a 220v Ovp
Sorensen DCR60-18B Power Supply 0 - 60V 0 - 18A in stock
Sorensen DCR60-30B Power Supply 0-60v 0-30a
Sorensen DCR60-30B2 DC Power Supply 0 - 60V 0 - 30A
Sorensen DCR60-45B Power Supply 0-60v 0-45a 220 VAC
Sorensen DCR60-45B2 Power Supply 0 - 60V 0 - 45A 220VAC Over-Voltage http://www.kandelelex.com/jpegs/sordcr60-45b2.jpg in stock
Sorensen DCR60-9B Power Supply 0 - 60V 0 - 9A in stock
Sorensen DCR7-300B Power Supply 0 - 7V 0 - 300A
Sorensen DCR80-125T Power Supply 0 - 80V 0 - 125A 480VAC 3-Phase In http://www.kandelelex.com/jpegs/sordcr80-125t.jpg in stock
Sorensen DCR80-12B Power Supply 0-80v 0-12A
Sorensen DCR80-33B Power Supply 0-80v 0-33a
Sorensen DCR80-6B Power Supply 0-80v 0-6a
Sorensen DCS100-30 M9A Programmable DC Power Supply 0-100V 0-30A GPIB This power supply is a Sorensen DCS80-37 M80 which has a modified output to 0 to 80 volts and 0 to 30 amps. It has programming via GPIB. in stock
Sorensen DCS150-20 DC Power Supply 0 - 150V 0 - 20A Digital Switchin
Sorensen DCS150-7 Power Supply 0 - 150V 0 - 7A Switcher http://www.kandelelex.com/jpegs/sordcs150-7.jpg in stock
Sorensen DCS150-7E DC Power Supply 0-150V 0-7A switching
Sorensen DCS150-7E M9C Programmable DC Power Supply 0-150V 0-7A GPIB The Sorenson DCS150-7E programmable power supply utilizes switchmode technology to achieve high power density in a low profile chassis. The design platform provides a highly reliable power supply for years of constant use.

Features:
High Power Densit
Sorensen DCS20-50 DC Power Supply 0 - 20V 0 - 50A Switching in stock
Sorensen DCS20-50E Power Supply 0-20v 0-50a Switcher
Sorensen DCS20-50E M9C Programmable DC Power Supply 0 - 20V 0 - 50A GPIB
Sorensen DCS300-3.5 Power Supply 0 - 300V 0 - 3.5A Switcher http://www.kandelelex.com/jpegs/sordcs300-3.5.jpg in stock
Sorensen DCS300-3.5 M9A Programmable DC Power Supply 0-300V 0-3.5A GPIB in stock
Sorensen DCS300-3.5E DC Power Supply 0 - 300V 0 - 3.5A Switching The DCS300-3.5E programmable power supply incorporates current mode switching rates up to 100 kHz in high power density, low profile chassis. Utilizing unique packaging techniques, the DCS300-3.5E provides continuous full output power of 1KW in any volt/a
Sorensen DCS300-3.5E M9C Programmable DC Power Supply 0-300V 0-3.5A GPIB
Sorensen DCS33-33 Power Supply 0 - 33V 0 - 33A Switching http://www.kandelelex.com/jpegs/sordcs33-33.jpg
Sorensen DCS33-33 M9A Programmable Power Supply 0-33v 0-33a GPIB/RS232 in stock
Sorensen DCS33-33E DC Power Supply 0 - 33V 0 - 33A Switcher The DCS33-33E programmable power supply incorporates current mode switching rates up to 100 kHz in high power density, low profile chassis. Utilizing unique packaging techniques, the DCS33-33E provides continuous full output power of 1KW in any volt/amp c http://www.kandelelex.com/jpegs/sordcs33-33e.jpg in stock
Sorensen DCS33-33E M9C Programmable Power Supply 0 - 33V 0 - 33A GPIB / http://www.kandelelex.com/jpegs/sordcs33-33e m9c.jpg
Sorensen DCS40-25 Power Supply 0 - 40V 0 - 25A Switching http://www.kandelelex.com/jpegs/sordcs40-25.jpg in stock
Sorensen DCS40-25E Power Supply 0 - 40V 0 - 25A Switching http://www.kandelelex.com/jpegs/sordcs40-25e.jpg
Sorensen DCS40-25E M9C Programmable DC Power Supply 0 40V 0 - 25A GPIB The DCS40-25E M9C programmable power supply incorporates current mode switching rates up to 100 kHz in high power density, low profile chassis. Utilizing unique packaging techniques, the DCS40-25E M9C provides continuous full output power of 1KW in any vo
Sorensen DCS40-25EM9C Programmable DC Power Supply 0 40V 0 - 25A GPIB The DCS40-25E M9C programmable power supply incorporates current mode switching rates up to 100 kHz in high power density, low profile chassis. Utilizing unique packaging techniques, the DCS40-25E M9C provides continuous full output power of 1KW in any vo
Sorensen DCS40-25M37 Power Supply 0-40V 0-25A Switcher 220 VAC Input http://www.kandelelex.com/jpegs/sordcs40-25m37.jpg
Sorensen DCS40-25M9C Power Supply 0-40v 0-25a GPIB Switcher http://www.kandelelex.com/jpegs/sordcs40-25m9c.jpg
Sorensen DCS40-30E DC Power Supply 0-40V 0-30A 1200W The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a lo
Sorensen DCS40-75 Power Supply 0-40V 0-75A Switching http://www.kandelelex.com/jpegs/sordcs40-75.jpg
Sorensen DCS40-75E DC Power Supply 0-40V 0-75A Switching
Sorensen DCS40-75M9C Programmable DC Power Supply 0-40V 0-75AGPIB The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a lo
Sorensen DCS50-20E Power Supply 0-50V 0-20A Switching
Sorensen DCS50-24E DC Power Supply 0-50V 0-24A 1200W
Sorensen DCS55-55 Power Supply 0 - 55V 0 - 55A Switching http://www.kandelelex.com/jpegs/sordcs55-55.jpg in stock
Sorensen DCS55-55M9C Programmable DC Power Supply 0 - 55V 0 - 55A Swi
Sorensen DCS600-1.7 Power Supply 0-600v 0-1.7A Switcher http://www.kandelelex.com/jpegs/sordcs600-1.7.jpg
Sorensen DCS600-1.7E DC Power Supply 0 - 600V 0 - 1.7A 1KW The DCS600-1.7E is a 1 kW DC programmable power supply utilizing switch-mode technology to achieve high power density in a low profile chassis. The DCS600-1.7E provides continuous full output power in any volt/amp combination within the rated output volta in stock
Sorensen DCS600-1.7E M9C DC Power Supply 0 - 600V 0 - 1.7A Switching Output Ratings: Output Voltage 0 - 600V; Output Current 0 - 1.7A; Output Power 1020W
Line Regulation: Voltage 600mV; Current 1.7mA
Load Regulation: Voltage 600mV ; Current 1.7mA
Mete Accuracy: Voltage 7.0V; Current 0.018A
OVP Adjusment Range: 30
in stock
Sorensen DCS60-18 Power Supply 0 - 60V 0 - 18A Switching http://www.kandelelex.com/jpegs/sordcs60-18.jpg in stock
Sorensen DCS60-18E Power Supply 0-60v 0-18a Switcher
Voltage: 0-60
Voltage resolution: 0.02%
Ripple: 20 mV RMS typical
Current: 0-18
Regulation Voltage and Current(Line or Load): 0.1%


in stock
Sorensen DCS60-18EM9C Programmable Power Supply 0-60v 0-18a GPIB
Sorensen DCS60-50 Power Supply 0-60V 0-50A Switcher Voltage Resolution: 0.02%
Ripple (mV RMS or P-P): See table
Regulation (Line or Load)
Voltage: 0.1%
Current: 0.1%
Transient Response: Typically recovers in <1 ms to 1% of steady-state output voltage (within 1% of Vmax) for 70-100% or 100
http://www.kandelelex.com/jpegs/sordcs60-50.jpg
Sorensen DCS60-50 M9C Programmable DC Power Supply 0-60V 0-50A GPIB The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a lo in stock
Sorensen DCS80-13 Power Supply 0-80V 0-13A Switcher http://www.kandelelex.com/jpegs/sordcs80-13.jpg
Sorensen DCS80-13E Power Supply 0-80V 0-13A Switcher The DCS80-13E is a 1kw DC programmable power supply using switch-mode technology to achieve high power density in a low profile chassis. The DCS80-13E provides continuous full power output in any volt/amp combination within the rated output voltage and
Sorensen DCS80-13EM9C Programmable Power Supply 0 - 80V 0 - 13A Switch http://www.kandelelex.com/jpegs/sordcs80-13em9c.jpg in stock
Sorensen DCS80-13M9A Programmable Power Supply 0-80v 0-13a GPIB The DCS80-13E is a 1kw DC programmable power supply using switch-mode technology to achieve high power density in a low profile chassis. The DCS80-13E provides continuous full power output in any volt/amp combination within the rated output voltage and http://www.kandelelex.com/jpegs/sordcs80-13m9a.jpg
Sorensen DCS80-37 Power Supply 0 - 80V 0 - 37A Switching The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a lo in stock
Sorensen DCS80-37 M80 Programmable DC Power Supply 0 - 100V 0 - 30A GPI he DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a low in stock
Sorensen DCS80-37 M9C Programmable DC Power Supply 0-80V 0-37A GPIB The DCS Family of 1 kW, 1.2 kW and 3 kW programmable power supplies utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a lo
Sorensen DCS80-37M80 Programmable DC Power Supply 0 - 100V 0 - 30A GPI Please note this supply is rated at 100V, 30A unlike the standard 80V 37A configuration. Requires three phase input power, however it can be operated using single phase 190-250 VAC with slightly reduced (2500W) output capacity.

The DCS Family of progr
Sorensen DCS8-125E Power Supply 0 - 8V 0 - 125A Switching
Sorensen DHP100-100 M9D Programmable DC power Supply 0-100V 0-110 Switcher
Sorensen DHP100-30 DC Power Supply 0 - 100V 0 - 30A Digital Switchin The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-curr in stock
Sorensen DHP120-16 Power Supply 0 - 120V 0 - 16A Switching 220 VAC in stock
Sorensen DHP20-150M9D Programmable Power Supply 0-20V 0-150A GPIB
Sorensen DHP250-20 M9D Programmable DC power Supply 0-250V 0-20A GP-IB 20 in stock
Sorensen DHP300-10 DC Power Supply 0-300V 0-10A 190-253VAC 1ph in stock
Sorensen DHP300-100 DC Power Supply 0-300V 0-100A switching 200-240VAC
Sorensen DHP30-220 DC Power Supply 0-30V 0-220A Switching in stock
Sorensen DHP400-25 M9D Programmable DC Power Supply 0-400V 0-25A GPIB The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-curr
Sorensen DHP400-50 DC Power Supply 0-400V 0-50A Switching
Sorensen DHP400-5M9D Programmable Power Supply 0-400v 0-5a GPIB
Sorensen DHP50-265 Power Supply 0 - 50V 0 - 265A Switching 190 - 25 Voltage: 0 to 50 VDC
Current: 0 to 265
Ripple: 15mV typical RMS
Programming: Analog(Standard) RS232, GPIB options.
http://www.kandelelex.com/jpegs/sordhp50-265.jpg
Sorensen DHP50-265M2 Power Supply 0-50v 0-265a Switching 432-528VAC 3ph
M2 option provides for 432-528 three phase input.
Voltage: 0 to 50 VDC
Current: 0 to 265
Ripple: 15mV typical RMS
Programming: Analog(Standard) RS232, GPIB options.
http://www.kandelelex.com/jpegs/sordhp50-265m2.jpg
Sorensen DHP50-40M9D Programmable DC Power Supply 0 - 50V 0 - 40A GPIB The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-curr
Sorensen DHP50-60 DC Power Supply 0 - 50V 0 - 60A Switching Digital The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-curr in stock
Sorensen DHP600-16 DC Power Supply 0-600V 0-16A 200-240VAC 3ph The DHP Family contains over 140 models ranging in output power from 2 kW to 30 kW in a single chassis. The 2 kW and 3 kW models are housed in a thin 2U (3.5 inches) high, 19 inches wide rackmount chassis. Programmable output voltages range from 5V to
6
in stock
Sorensen DHP60-110 DC Power Supply 0-60V 0-110A Switching 200-240VAC in stock
Sorensen DHP60-33M9D Programmable Power Supply 0 - 60V 0 - 33A GPIB http://www.kandelelex.com/jpegs/sordhp60-33m9d.jpg in stock
Sorensen DHP60-50 DC Power Supply 0 - 60V 0 - 50A Switching 200 - The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-curr
Sorensen DHP80-250 Power Supply 0-80v 0-250a 208VAC 3ph Switcher OUTPUT
Voltage, Current, and Ripple:0-80, 0-250, 25mV
Regulation (Line or Load)
Voltage: 0.1% of maximum rated output
Current: 0.5% of maximum rated output
Transient Response: 2 ms to steady state output voltage (within 2% of Vmax) for 30% step l
http://www.kandelelex.com/jpegs/sordhp80-250.jpg
Sorensen DHP80-375 Power Supply 0 - 80V 0 - 375A Switcher 190 - 253 Output: 0-80Vdc 0-375 Amp
Ripple: 15mV (typical)
Regulation (Line or Load)
Voltage: 0.1% of maximum rated output
Current: 0.5% of maximum rated output
Transient Response: 2 ms to steady state output voltage (within 2% of Vmax) for 30% step load c
http://www.kandelelex.com/jpegs/sordhp80-375.jpg
Sorensen DHP80-37M3M9D Programmable DC Power Supply 0 - 80V 0 - 37A GPIB The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-curr in stock
Sorensen DHP8-350 DC Power Supply 0 - 8V 0 - 350A Switching 200 - 2 in stock
Sorensen DLM300-13E DC Power Supply 0 - 300V 0 - 13A Switching 180 - High Power Density - 3 kW and 4 kW models, 2U (3.5") high, 19" wide
Pushbutton preview of settings without output enabled
Standard analog programming
Optional IEEE-488.2 and RS-232
Optional optically isolated analog programming
Constant voltage
Sorensen DLM40-100 DC Power Supply 0 - 40V 0 - 100A Digital Switch
Sorensen DLM40-15 M85 DC Power Supply 0 - 40V 0 - 15A The DLM 600W series of programmable power supplies is designed to provide continuously variable output voltage and current for a broad range of applications in a compact 1U (1.75 inches) high, half-rack (8.5 inch) wide chassis.

With the use of Zero Vol
Sorensen DLM40-15 M9G Programmable DC Power Supply 0-40V 0-15A GPIB The DLM 600W series of programmable power supplies is designed to provide continuously variable output voltage and current for a broad range of applications in a compact 1U (1.75 inches) high, half-rack (8.5 inch) wide chassis.

With the use of Zero Vol
in stock
Sorensen HPD15-20M9 Programmable Power Supply 0 - 15V 0 - 20A GPIB http://www.kandelelex.com/jpegs/sorhpd15-20m9.jpg in stock
Sorensen HPD60-5M9 Programmable Power Supply 0-60v 0-5a GPIB
Sorensen LH75-5 Power Supply 0 - 75V 0 - 5A Digital Meters in stock
Sorensen PRO300-33T Power Supply 0 - 300V 0 - 33A 480VAC 3-Phase The PRO-T Series, 10KW three phase power supplies meet the sophisticated control and packaging requirements of high power test and measurement applications. Other features are output for remote meters, remote OVP programming and remote shutdown. The PRO
Sorensen QRB15-2 Power Supply 0 - 15V 0 - 2A
Sorensen QRC40-4A Power Supply 0 - 40V 0 - 4A
Sorensen QRD15-2 Power Supply 0 - 15V 0 - 2A
Sorensen QRS40-2 Power Supply 0 - 40V 0 - 2A
Sorensen SGA400-12C-2AAA Programmable DC Power Supply 0-400V 0-12A GPIB RS2 The Sorensen SG series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a fu in stock
Sorensen SGA80-313C-IDAA DC Power Supply 0-80V 0-313A 187-242VAC 3ph The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry.
At the
Sorensen SRL20-12 Power Supply 0 - 20V 0 - 12A
Sorensen SRL20-25 Power Supply 0 - 20V 0 - 25A in stock
Sorensen SRL20-50 Power Supply 0 - 20V 0 - 50A in stock
Sorensen SRL40-12 Power Supply 0 - 40V 0 - 12A
Sorensen SRL40-25 Power Supply 0 - 40V 0 - 25A in stock
Sorensen SRL40-50 Power Supply 0 - 40V 0 - 50A 220VAC in stock
Sorensen SRL40-6 Power Supply 0 - 40V 0 - 6A in stock
Sorensen SRL60-17 Power Supply 0-60v 0-17A
Sorensen SRL60-35 Power Supply 0-60v 0-35a
Sorensen SRL60-8 Power Supply 0 - 60V 0 - 8A Over-Voltage Protect in stock
Sorensen XTD2020M5 Dual Power Supply 0 - 20V 0 - 3A Dual 20 volt 3 amp supply with front panel or remote programming of voltage, current, on/off and OVP. Simultaneous large digital readout of voltage and current. Dual mode with auto crossover. in stock
Sorensen XTS120-0.5 Power Supply 0 - 120V 0 - .5A Digital Readout
0-120 Vdc 0-0.5 Amp
Constant Voltage Mode
Ripple: 1 mV RMS
Regulation: Line and load combined 0.02% of Vmax + 4 mV
Transient Response: Typically recovers in 100 s to within 0.05% of steady-state output voltage. 50% load change in the range of 2
in stock
Sound Technology 1700B Distortion Measurement System Combination analyzer and oscillator. Frequency range 10.0 Hz to 110 kHz. Set level input 0.1 V to 300 V. Distortion measurement range 0.001% to 100%. Call for price and availablility of the following options: 03-provides automatic set level; 04-IM d http://www.kandelelex.com/jpegs/st1700b.jpg
Spectracom 8131 Frequency Standard Oscillator Outputs: 0.1, 1, 5, 10MHz. Short-term stability: 2x10(-10). Front panel frequnecy control. Requires Tek TM500 mainframe. in stock
Stanford Research Sys SR530 01 Programmable Dual-phase Lock-in Amplifier .5Hz-100 The SR510 and SR530 are analog lock-in amplifiers which can measure AC signals as small as nanovolts in the presence of much larger noise levels. Both the single phase SR510 and the dual phase SR530 have low-noise voltage and current inputs, high dynam http://www.kandelelex.com/jpegs/srssr530 01.jpg in stock
Stanford Research Sys SR550 FET Lock-In Preamplifier The Stanford Research SR550 Voltage Preamplifier is designed to work with SRS lock-in amplifiers. The SR550 may also be operated independently with appropriate biasing(20VDC, +5VDC).
Features:
3.6nV/uHz input noise
FET input, 100M ohm input impedanc
http://www.kandelelex.com/jpegs/srssr550.jpg in stock
Stanford Research Sys SR552 Low Noise Preamplifier Used with SRS lock-in amplifiers. Bipolar input, 100K ohm input impedance. Adjustable gain: 10, 20 50 or 100 (automatically set by SR510) in stock
Stanford Research Sys SR570 Low-noise Current Preamplifier The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low temperature and other measurements.

Gain
http://www.kandelelex.com/jpegs/srssr570.jpg
Stanford Research Sys SR620 Time Interval Counter 1.3GHz Frequency: 0.001Hz to 300MHz via comparator inputs; 40MHz to 1.3GHz via internal prescalers. 1nHz Resolution. 25ps single-shot time resolution. 0.001 Degree phase resolution. Graphical output to XY scope, hardcopy to printers and ploters, GP-IB and http://www.kandelelex.com/jpegs/srssr620.jpg
Stanford Research Sys SR623 Rubidium Time Base-2GHz Prescaler The Stanford Research SR623 is a Rubidium time base and 2GHz prescaler used as a stand-alone or is typically used with the SR620 counter to make it an SR625 counter.
Frequency: 10MHz; Output: 1Vp-p sine wave
Accurcy: +/-5 x 10(-11)
Warm-up: 10 minutes
in stock
Stanford Research Sys SR625 Frequency Counter with Rb Timebase The SR625 Frequency Counter is a NIST traceable frequency counting standard for calibarating base stations, transmitters and many other types of communication systems. It combines the high resolution and wide variety of features found in the SR620 coun http://www.kandelelex.com/jpegs/srssr625.jpg
Stanford Research Sys SR630 16-Channel Thermocouple Monitor Designed to read, scan, print, and log temperatures or voltages. Thermocouple: type B,E,J,K,R,S,T; displays degrees C,F,K with 0.1 C resolution and 0.5 accuracy. Voltmeter: ranges; 9.999mVdc to 99.99Vdc with 0.05% gain accuracy. Scanning and Data http://www.kandelelex.com/jpegs/srssr630.jpg
Stanford Research Sys SR640 Programmable Dual Low-pass Filter The SR600 series consists of three dual-channel instruments. Each instrument channel has a low-noise preamplifier, a precision high pass or low pass filter section, and an output amplifier. The filters are 8-pole, 6-zero elliptic-type with 115 dB per
Stanford Research Sys SR715 LCR Meter The SR715 LCR Meter measure passive components with as little as 0.05% error. These easy-to-use instruments are quick to setup, adjust and calibrate. The SR715 is ideal for applications such as incoming inspection, quality control, automated test, and
Stanford Research Sys SR760 FFT Spectrum Analyzer DC - 100KHz Features: 90dB dynamic range; 16-bit A/D conversion; PSD & 1/3 octave measurements; harmonic, band & sideband analysis; 100KHz real-time bandwidth, internal & external triggering; linear and exponential averaging; hardcopy output to printers & plotters; http://www.kandelelex.com/jpegs/srssr760.jpg
Stanford Research Sys SR780 Dual Channel Dynamic Signal Analyzer DC-102.4KHz SR780 Dynamic Signal Analyzer
Features
DC to 102.4 kHz bandwidth
90 dB dynamic range
Low-distortion synthesized source
145 dB dynamic range in swept-sine mode
Real-time octave analysis
Up to 32 Mbyte memory
GIF, EPS, PCX, HP-GL graphics outp
http://www.kandelelex.com/jpegs/srssr780.jpg
Stanford Research Sys SR785 Dual-Channel Dynamic Signal Analyzer DC - 102.4KHz The SR785 Two-Channel Dynamic Signal Analyzer is a precision, full-featured signal analyzer that offers state-of-the-art performance at a price that's less than half that of competitive analyzers. Building on its predecessor, the SR780, the SR785 incor http://www.kandelelex.com/jpegs/srssr785.jpg
Stanford Research Sys SR810 DSP Lock-In Amplifier 1 MHz To 102.4 KHz The SR810 Lock-In Amplifier and SR830 Lock-In Amplifier provide high performance at a reasonable cost. The SR810 displays magnitude only. This instrument use digital signal processing (DSP) to replace the demodulators, output filters, and amplifiers f http://www.kandelelex.com/jpegs/srssr810.jpg
Stanford Research Sys SR830 DSP Dual Phase Lock-In Amplifier 1 mHz to 102.4 kHz frequency range
>100 dB dynamic reserve
5 ppm/C stability
0.01 degree phase resolution
Time constants from 10 s to 30 ks
(up to 24 dB/oct rolloff)
Auto-gain, -phase, -reserve and -offset
Synthesized reference source
GPI
http://www.kandelelex.com/jpegs/srssr830.jpg
Stanford Research Sys SR850 DSP Dual Phase Lock-In Amplifier The SR850 is a digital lock-in amplifier based on an innovative DSP (Digital Signal Processing) architecture. The SR850 boasts a number of significant performance advantages over traditional lock-in amplifiers-higher dynamic reserve, lower drift, lower http://www.kandelelex.com/jpegs/srssr850.jpg
Stoddart 91889-1 Standard Gain Horn ( 2.3 - 4.4GHz ) in stock
Stoddart 92341-1 Horn Antenna Mount Used with Stoddart 91889-1.
Struthers Electronic Corp BC150A Crystal Detector 10MHz - 12GHz in stock
Systron Donner 6051 Electronic Counter
Taylor Winfield MK2.3 Thermonic Induction Heater Water cooled. Condition unknown; may be used as a parts unit.
TDK RF Solutions VC04-SI300 RF Shielded Color Video Camera System for EMC Test The TDK VC-04 Color Video Camera is a high performance CCD specifically designed for remote monitoring of equipment under EMC testing. The camera is also ideal for wide angle anechoic chamber monitoring, shielded access control, and test action archiving.
Techron 7560 Power Amplifier DC-45KHz 1000 Watts into 4 Ohms
Techron 7570 Power Amplifier DC-45KHz 1000 Watts into 4 Ohms The Techron 7560/70 series of amplifiers comes from one of Crown's highest powered amplifiers-the M600. Its design and construction has withstood the test of time. Its reputation was one of pushing the upper limits of power to the extreme! It has a tradit
Tegam 2348 High Current Precision Power Amplifier DC - 2MHz 1 The Model 2348 2 MHz Power Amplifier has a continuous current output of 750 mA at voltages up to 50 Vp-p. This provides 18.75 watts of AC or DC output power to 500 kHz. The instrument's bandwidth ranges from DC to 2 MHz.

An independent, buffered, volt
Tegam 2714A Arbitrary Waveform Generator GPIB Model 2714A
*Harmonic Distortion: -65 dB
*Vertical Resolution: 12 Bit
*Sample Rate: 0.1 S/s to 20 MS/s
*Programmable Waveform Sequencer
*Standard GPIB, RS-232 Interface
*Trigger-sync for multiple unit operation
in stock
Tegam 2730 Function /Arbitrary Waveform Generator 50MHz The 2700 series of Function/Arbitrary Waveform Generators
combines direct digital synthesis function generator architecture with
the unmatched precision of true arbitrary waveform generators for the
best of both worlds in signal generation.
Create a
http://www.kandelelex.com/jpegs/teg2730.jpg in stock
Tektronix 012-1221-00 Sampling Head Extender Cable
Tektronix 015-0310-01 Pulse Head for CG5001 in stock
Tektronix 015-0385-00 Diplexer Used with 490-Series in stock
Tektronix 067-0587-01 Calibration Fixture for 7000 Series Mainframes in stock
Tektronix 067-0587-02 7000-series Calibration Fixture
Tektronix 067-0599-00 Scope Cal Fixture 576 Calibrator in stock
Tektronix 1101 Probe Power Supply Powers up to 2 Tek active FET probes(such as P6201, P6201, P6230). in stock
Tektronix 1101A Probe Power Supply Powers up to 2 Tek active FET probes(such as P6201, P6201, P6230). in stock
Tektronix 1103 "Tekprobe" Power Supply The 1103 is an accessory power supply that provides external power to TEKPROBE BNC Interface probes. The 1103 allows customers to use probes requiring TEKPROBE interface power with any oscilloscope or digitizer that does not provide TEKPROBE BNC power. http://www.kandelelex.com/jpegs/tek1103.jpg in stock
Tektronix 11301 Programmable Oscilloscope Mainframe Up to 500MHz bandwidth at probe tip(depending on plug-in). Menu-driven touch screen. Automatic time and amplitude measurements. 500MHz universal counter/timer. Dual delayed sweeps. IEEE-488 and RS-232C. http://www.kandelelex.com/jpegs/tek11301.jpg in stock
Tektronix 11302A 500MHz Programmable Oscilloscope Up to 8 channels. Built-in 750MHz counter. Touch-screen menu driven operation. Automatic time and amplitude measurements. Dual delayed sweeps. 6cm/ns visual writing speed. GP-IB and RS232-C interfaces. http://www.kandelelex.com/jpegs/tek11302a.jpg in stock
Tektronix 11401 500MHz Programmable Digitizing Oscilloscope 20MS/s digitizing rate. Up to 8 channels of display and acquisition. Waveform processing and automatic pulse parameters. Multiple 10K point waveform records. Dual time bases, 5.12ns to 1024s record duration. Up to 14 bit vertical resolution. GP-IB http://www.kandelelex.com/jpegs/tek11401.jpg in stock
Tektronix 11402 Digitizing Oscilloscope Mainframe Bandwidth: DC to 1GHz with 10-bit resolution. Built-in time bases with 5.11ns to 1024s record duration and 20MS/s max sampling rate. Features: On-board measurement statistics, Advanced waveform processing, 8 channels of acquisition, Selectable 512 to
Tektronix 11802 Digital Sampling Oscilloscope Tektronix 11802 20-GHz Digital Sampling Oscilloscope Mainframe. 4 channels, 200 KSa/s, built-in delay lines
Includes a built-in dual compensated delay line with trigger pickoff.
Sampling heads available seperately.
http://www.kandelelex.com/jpegs/tek11802.jpg in stock
Tektronix 11A32 Two-Channel Amplifier DC to 400MHz. 1mV to 10V/div. 1M ohm or 50 ohm. in stock
Tektronix 11A33 Differential Comparator Bandwidth: DC to 150MHz. Deflection factors: 1mV to 10V/div. Input Impedance: 50 ohm, 1M ohm, or 1G ohm. Features: Very high resolution, DC offset, High common mode rejection, Fast overdrive recovery. http://www.kandelelex.com/jpegs/tek11a33.jpg
Tektronix 11A34 Four-Channel Vertical Amplifier Calibrated deflection factors: 1mV to 10V/div in 1-2-5 sequence. Bandwidth: DC to 300MHz. Calibrated DC offset. http://www.kandelelex.com/jpegs/tek11a34.jpg in stock
Tektronix 11A52 600MHz Vertical Amplifier Vertical deflection: 1mV to 10V/div, 2 channels. Input impedance: 50 ohm. in stock
Tektronix 11A71 Single Channel Amplifier Bandwidth: DC to 1GHz. Calibrated deflection factors: 10mV to 1V/div. 50 ohm input.
Tektronix 11A72 Two-Channel Amplifier Bandwidth: DC to 1GHz. Deflection factors: 10mV to 1V/div. 50 ohm input impedance. http://www.kandelelex.com/jpegs/tek11a72.jpg in stock
Tektronix 1230 Logic Analyzer Flexible mainframe can be configured as a general purpose basic 16 channel timing and state analyzer expandable up to 64 channels. Features: 100MHz aSynchronous sampling; 100MS/s digitizing oscilloscope card; 25MHz Synchronous sampling; 2K memory depth in stock
Tektronix 1240 Logic Analyzer Hardware analysis up to 100MHz sample, glitch triggering and auto run mode; software analysis to 72 channels, 14 levels of triggering and mnemonic disassembly; each mainframe has four card slots which accommodate any combination of 9 channel(1240D1) and in stock
Tektronix 1241 Color Logic Analyzer Hardware analysis up to 100MHz sample, glitch triggering and auto run mode; software analysis to 72 channels, 14 levels of triggering and mnemonic disassembly; each mainframe has four card slots which accommodate any combination of 9 channel(1240D1) and http://www.kandelelex.com/jpegs/tek1241.jpg in stock
Tektronix 12RS02 64k Ram Pack in stock
Tektronix 1410R NTSC SYNC Generator Sub carrier frequency is 3.579545MHz 10Hz. Pull-in frequency sub carrier range of 50Hz. Configured with the following modules: SPG2A SYNC Generator, TSG-1 Color Bars, TSG-2 Convergence, and TSG3 Linearity. in stock
Tektronix 1410R/04 NTSC Generator Fully configured with the following modules: SPG2A SYNC Generator, TSG3 Linearity, TSG5 Pulse and Bar, TSG6 Multiburst, TSG7 Color Bars and TSP1 Switcher. in stock
Tektronix 1430 Random Noise Measuring Set Provides random noise measurement on an in-service basis when used with a waveform monitor. Includes a program channel and a monitor channel. in stock
Tektronix 1440 Automatic Video Corrector Provides VIRS referenced correction of video signal amplitude, chrominance to luminance gain ratio, blacklevel, chrominance phase, burst gain and sync gain. in stock
Tektronix 1441 VIR Signal Deleter/inserter Deletes signals on selected lines during the vertical interval, and inserts the VIR signal. in stock
Tektronix 1450-1 TV Demodulator / Down Converter Provides an accurate link between the transmitter or CATV RF signals and baseband video measuring equipment. Also demodulates off-air signals for repeater sites or videotaping. Eliminates distortion in reproduced signal characteristics. Option 03 is http://www.kandelelex.com/jpegs/tek1450-1.jpg in stock
Tektronix 1470 Video NTSC Color Sync and Test Signal Generator A compact, economical unit consisting of a full color genlock sync generator and a full selection of high quality test signals. http://www.kandelelex.com/jpegs/tek1470.jpg in stock
Tektronix 147A NTSC Signal Generator Supplies all the test signals commonly used for test and measurement of video transmission systems; the signals generated are available as full-field composite-video test signals and as Vertical Interval Test Signals (VITS) inserted on an incoming compo http://www.kandelelex.com/jpegs/tek147a.jpg in stock
Tektronix 1480R NTSC Waveform Monitor Digital selection of line and field; 0.2% amplitude measurement accuracy; 15-line display for VIR applications. Call for price and availability of the following option: 01-Probe input. in stock
Tektronix 1485R NTSC/PAL Waveform Monitor Dual standard waveform monitor features bright CRT for vertical interval testing, advanced measurement modes, amplitude measurement approaching 0.2%, and digital selection of line and field. Also provides a 15-line display for VTR applications. This u
Tektronix 149A NTSC Test Generator Features VITS generation, insertion and deletion; Sync and burst regeneration; program signal protection; full field test or split field color bar signals. in stock
Tektronix 1502B Metallic TDR Cable Tester Max Range: 2000ft/625m with 0.004ft/0.001m resolution. Dist/Div: 0.1 to 200Ft/div; 0.025 to 50m/div. Faults of 0.5 ohm and multiple faults of 0.8" can be resolved. Direct distance readout; High-resolution LCD display with zoom; Menu-driven setup; hel http://www.kandelelex.com/jpegs/tek1502b.jpg in stock
Tektronix 1502C Metallic TDR Cable Tester The 1502C is designed to quickly and easily locate opens, shorts, crimps, and other defects in metallic cables. The 1502C can measure up to 2,000 feet (625 meters).

Features & Benefits
Backlit LCD Display Assures Sharp Images in Any Lighting Conditi
http://www.kandelelex.com/jpegs/tek1502c.jpg
Tektronix 1503B Metallic TDR Selectable widths of 2, 10 , 100, or 1000 nano-seconds and pilse output impedances of 50, 75, 93 or 125 ohm. Distance range to 50,000 feet/10,000 meters with 1.2 in/3m readout resolution. 1% accuracy. LCD display with zoom; Menu-driven setup; help mo http://www.kandelelex.com/jpegs/tek1503b.jpg in stock
Tektronix 1503C Metallic TDR Features
Backlit LCD Display Assures Sharp Images in Any Lighting Condition
Menu-driven Operation for Easy Test Set-up
Help Screens Provide Information on Instrument Operation and Measurements
Information Screens Provide Cable Impedance and Vp Valu
http://www.kandelelex.com/jpegs/tek1503c.jpg in stock
Tektronix 1710B NTSC Waveform / Burst Phase Monitor Features: Easy operation/cost efective; Burst phase indicator; Dual filter display; Bright CRT display. http://www.kandelelex.com/jpegs/tek1710b.jpg in stock
Tektronix 1710J Waveform Monitor Dual-Filter Display The Tektronix 1710J waveform monitor provides high quality basic waveform monitoring at an economical price. This instrument includes key features of more expensive monitors, making the 1710J suitable for operation in camera-control consoles and video- http://www.kandelelex.com/jpegs/tek1710j.jpg in stock
Tektronix 1720 NTSC Vectorscope Features: Simultaneous channel A and B display, Stereo audio phase measurement, R-Y output for differential phase measurement. http://www.kandelelex.com/jpegs/tek1720.jpg in stock
Tektronix 1721 PAL Vectorscope Features: Simultaneous channel A and B display, Stereo audio phase measurement, R-Y output for differential phase measurement. http://www.kandelelex.com/jpegs/tek1721.jpg in stock
Tektronix 1721SCH PAL Vectorscope SCH Capability The TEKTRONIX 1720SCH-Series is an 8-1/2-inch wide by 5-1/4-inch high Vectorscope, weighing 8-1/2 pounds. The product offers the vector and audio features of the 1720-Series vectorscope, plus SCH phase error measurement capabilities. in stock
Tektronix 1725 Pal/NTSC Vectorscope Half-rack unit provides simultaneous channel A and B display, stereo audio phase measurement and R-Y output for different phase measurement.
Tektronix 1730 NTSC Waveform Monitor Features: Complete line select, Simultaneous channel A and B display, Differential gain measurements, One button front-panel recall, Dual filter display, VTR servo rates. http://www.kandelelex.com/jpegs/tek1730.jpg in stock
Tektronix 1730D Digital Composite NTSC Waveform Monitor Waveform monitor with direct digital inputs for serial and parallel composite signals along with two analog inputs for composite video signals and input for an external reference. Full time DAC output and menu screens for instrument setup. http://www.kandelelex.com/jpegs/tek1730d.jpg
Tektronix 1730HD High Definition Waveform Monitor Features: HDTV sweep speeds; Full 30MHz bandwidth; Six video input channels; Parade and overlay displays; Accepts tri-level sync; Onscreen readouts; Half-rack width.
Tektronix 1731D Digital Composite PAL Waveform Monitor The Tektronix 1731D functions as a standard waveform monitor, with direct signal inputs for serial and parallel composite signals.
Features:
2 Analog composite inputs
2 Serial digital composite inputs
1 Parallel digital composite input
Passive loop-t
Tektronix 1735 Dual-Standard Waveform Monitor ( NTSC & PAL ) The Tektronix 1730 Series Waveform Monitors and 1720 Series Vectorscopes provide comprehensive television signal monitoring for both NTSC and PAL applications. These versatile instruments are light weight, half-rack width and have bright CRTs for video http://www.kandelelex.com/jpegs/tek1735.jpg in stock
Tektronix 1740 NTSC Waveform / Vector Monitor The 1740 Waveform / Vector Monitor is well-suited for portable applications where a small, lightweight monitor is needed, and SCH capability is not required. It is appropriate for many VTR bridge applications, providing remote control and 90/100 Hz swe http://www.kandelelex.com/jpegs/tek1740.jpg in stock
Tektronix 1740A NTSC Waveform / Vector Monitor The 1740A/1750A/1760 Series make up a family of analog video waveform/vector monitors with progressive features in support of today's demanding television environment. Each model in the series provides improved video performance and ease of operation a http://www.kandelelex.com/jpegs/tek1740a.jpg in stock
Tektronix 1750 NTSC Waveform/vector/sch Monitor 8-Video inputs; waveform and vector displays; picture display for signal identification; stereo audio phase/amplitude display; time code waveform display. in stock
Tektronix 1750A NTSC Vector Scope / Waveform / Sch Monitor 8-Video inputs; waveform and vector displays; picture display for signal identification; stereo audio phase/amplitude display; time code waveform display. http://www.kandelelex.com/jpegs/tek1750a.jpg
Tektronix 1751 Pal Waveform / Vector Monitor / Sch 8-Video inputs; waveform and vector displays; picture display for signal identification; stereo audio phase/amplitude display; time code waveform display.
Tektronix 1755A NTSC-PAL Waveform-Vector-SCH Monitor The 1740A/1750A/1760 Series make up a family of analog video waveform/vector monitors with progressive features in support of today's demanding television environment.
Each model in the series provides improved video performance and ease of operation and
Tektronix 176 Curve Tracer High Current Fixture Extends the capabilities of the 576 by providing pulsed collector operation to 200 amps peak and pulsed base steps to 20 amps peak. Select 10, 100, or 1000 watts max peak power. in stock
Tektronix 1760 NTSC/component Waveform/vector Monitor Features include: 8 video inputs, analog waveform monitoring, time and voltage cursors in waveform mode, composite vectorscope phase and amplitude cursors and stereo audio aplitude and phase monitoring. http://www.kandelelex.com/jpegs/tek1760.jpg in stock
Tektronix 1765 NTSC / PAL / Component Waveform / Vector Monitor Features two composite plus two component inputs; all composite features of the 1740A; Component vector, Lightning and Diamond displays; Component picture monitor output. http://www.kandelelex.com/jpegs/tek1765.jpg in stock
Tektronix 177 Standard Test Fixture in stock
Tektronix 1780R NTSC Video Measurement Set The 1780R NTSC Video Measurement Set Video Measurement Set provides full bandwidth analog processing, precision waveform and vector measurements, and polar SCH presentation with calibration mode. The unit has four loop-through video input channels. In http://www.kandelelex.com/jpegs/tek1780r.jpg in stock
Tektronix 184 Generator Time Mark
Tektronix 1900 NTSC Digital Generator 10-bit digital signal, RS-232C interface, genlock and program line control, PROM memory, standard full field signals: modulated ramp, field square wave, window, VIRS. Transmitter Test Set: multiburst, multipulse, color bars, convergence, composite, mod in stock
Tektronix 1910 NTSC Digital Generator / Inserter Studio, transmitter, and transmission test signals. 10-bit signal generation. RS-232-C control port. 4 external VITS inputs. http://www.kandelelex.com/jpegs/tek1910.jpg in stock
Tektronix 2213A 60 MHz Oscilloscope Bandwidth: DC to 60MHz; 2mV to 5v/div.; 5ns/div sweep rate; Features advanced trigger system, single time base delay, TV sync, and X-Y operation.
Tektronix 2215 Portable Oscilloscope Bandwidth: DC to 60MHz; 2mV to 5v/div.; Features advanced trigger system, dual time base, alternate sweep switching that can display 4 traces, TV sync, and X-Y operation.
Tektronix 2215A Portable Oscilloscope Bandwidth: DC to 60MHz; 2mV to 5v/div.; Features advanced trigger system, dual time base, alternate sweep switching that can display 4 traces, TV sync, and X-Y operation.
Tektronix 2220 Digital Storage Oscilloscope Bandwidth: DC to 60MHz with 5.8ns rise time. Deflection Factor: 2mV to 5V/div. Single Time Base: 0.05us to 0.5s/div (extended to 5ns with10x mag). In STORE mode extended to 5s/div. Digitizing Rates: 20MS/s at 5us/div and faster to 20 samples/s at 5s in stock
Tektronix 2221 Digital Storage Scope Bandwidth: DC to 60MHz with 5.8ns risetime. Vertical deflection: 2mV to 5V/div, 2 channels. Time base (single): 0.05us to 0.5s/div (5ns/div with 10x mag, 5s/div in store mode). Digitizing rates: 20MS/s at 5us/div and faster to 20 samples/s at 5s/div.
Tektronix 2225 Portable Oscilloscope Bandwidth: DC to 50MHz; Vertical sensitivity: 500uV/div; "Hands-free" triggering including HF and LF reject filtering, TV line and field and peak to peak auto triggering. x5, x10, and x50 magnification. in stock
Tektronix 222A Handheld Storage Oscilloscope 60MHz Newer version of Tek 222.
Tektronix 2230 Digital Storage Oscilloscope This portable oscilloscope is user friendly with menu-driven operation. Bandwidth: DC to 100MHz(storage or non-storage), Single-shot: 2MHz(single channel). Vertical deflection factors: 2 mV/div to 5V/div. Sweep Ranges: 0.05us to 0.5s/div. Triggering http://www.kandelelex.com/jpegs/tek2230.jpg in stock
Tektronix 2232 Digital + Analog Oscilloscope 100MHz 100ms/s This portable oscilloscope is user friendly with menu-driven operation. Bandwidth: DC to 100MHz(storage or non-storage), Single-shot: 2MHz(single channel). Vertical deflection factors: 2 mV/div to 5V/div. Sweep Ranges: 0.05us to 0.5s/div. Triggering http://www.kandelelex.com/jpegs/tek2232.jpg in stock
Tektronix 2235 Portable Oscilloscope Bandwidth: DC to 100MHz; Features dual time base, dual trace, single sweep trigger view, BW limit, 2mV/div sensitivity, and 5ns/div sweep. in stock
Tektronix 2236 Portable Oscilloscope / Counter / Timer / DMM Bandwidth: DC to 100MHz; Features dual time base, dual trace, single sweep trigger view, BW limit, 2mV/div sensitivity, and 5ns/div sweep. Uses 9-digit vacuum fluorescent panel display for counter/timer/ and DMM. Measures frequency, period, pulse widt http://www.kandelelex.com/jpegs/tek2236.jpg in stock
Tektronix 2236A Portable Oscilloscope/counter/DMM Bandwidth: DC to 100MHz; Features dual time base, dual trace, single sweep trigger view, BW limit, 2mV/div sensitivity, and 5ns/div sweep. Uses 9-digit vacuum fluorescent panel display for counter/timer/ and DMM. Measures frequency, period, pulse widt
Tektronix 224 Handheld Digital Oscilloscope Bandwidth: DC to 60MHz; 2-Channels; 5.8ns risetime; 10MS/s sample rate; 8-Bit vertical resolution; 100ns peak detect/glitch capture; RS-232 interface.
Tektronix 2245 Portable Oscilloscope Four channels with DC to 100MHz bandwidth and 2mV/div sensitivity. Dual time base with sweep speeds to 2ns/div. Trigger modes Include: Auto Level, Auto, Norm, TV Field, TV Line, Single Sweep. CRT readout of front panel settings. http://www.kandelelex.com/jpegs/tek2245.jpg in stock
Tektronix 2246 4-channel Oscilloscope Bandwidth: DC to 100MHz. Vertical: Channels 1 & 2: 2mV/div to 5V/div. Channel 3 & 4: 0.1v/div or 0.5v/div. Time Base: A: 0.5s/div to 20ns/div. B: 5ms/div to 20ns/div. (X10 magnification extends sweep rate to 2ns/div). Flexible triggering provides http://www.kandelelex.com/jpegs/tek2246.jpg
Tektronix 2246A 4-channel Oscilloscope With Voltmeter Bandwidth: DC to 100MHz. Vertical: Channels 1 & 2: 2mV/div to 5V/div. Channel 3 & 4: 0.1v/div or 0.5v/div. Time Base: A: 0.5s/div to 20ns/div. B: 5ms/div to 20ns/div. (X10 magnification extends sweep rate to 2ns/div). Flexible triggering provides http://www.kandelelex.com/jpegs/tek2246a.jpg
Tektronix 2247A Oscilloscope Counter / Timer Vertical Bandwidth (4-Channels): DC to 100MHz. Deflection Factors: Channels 1 & 2; 2mV/div to 5V/div, Channels 3 & 4; .1v/div and .5v/div. Features: 4 Independent channels, Auto setup of front panel with Store/Recall (20 setups), Dual time base with d http://www.kandelelex.com/jpegs/tek2247a.jpg
Tektronix 2335 Portable Oscilloscope Rugged and light weight for field service work this scope offers: Bandwidth: DC to 100MHz; 8 x 10 division CRT (0.8cm/div); Sensitivity: 5mV/div to 5v/div: Sweep rate: 0.05us/div to 0.5s/div. Dual trace, delayed time base.
Tektronix 2336 Portable Oscilloscope Bandwidth: dc to 100MHz with 3.5ns rise time. Vertical deflection: 5mV/div to 5V/div, 2 identical channels. Horizontal: 0.05us/div to 0.5s/div, calibrated sweep delay with DELTA TIME displayed in the flip-top cover. http://www.kandelelex.com/jpegs/tek2336.jpg in stock
Tektronix 2430 Digital Storage Oscilloscope Bandwidth: DC to 150MHz. Deflection Factor: 2mV to 5V/div. Horizontal Sweep A/B: 5ns/div to 5s/div. Single-shot storage bandwidth: 40MHz. Max sample rate: 10MS/s on two simultaneous channels. Vertical Resolution: 8 bits. Record Length: 1024 points http://www.kandelelex.com/jpegs/tek2430.jpg
Tektronix 2430A Digital Storage Oscilloscope Bandwidth: DC to 150MHz. Deflection Factor: 2mV to 5V/div. Horizontal Sweep A/B: 5ns/div to 5s/div. Single-shot Storage Bandwidth: 40MHz. Max Sample Rate: 10MS/s on two simultaneous channels. Glitch Capture: 2ns. Vertical Resolution: 8 bits. Reco http://www.kandelelex.com/jpegs/tek2430a.jpg
Tektronix 2440 Digitizing Oscilloscope 300MHz 500ms/s Sampling Rate: 500MS/s. Bandwidth: 300MHz(repetitive) 200MHz (single shot). Vertical Res: 8 bit. Glitch Capture: 2ns at 50% amplitude. GP-IB http://www.kandelelex.com/jpegs/tek2440.jpg
Tektronix 2445 Portable Oscilloscope Four input channels, 150MHz bandwidth. Fully annotated CRT shows scale factors, trigger level, voltage, time, frequency, phase, and ratios. Vertical sensitivity 2mV/div. Sweep speeds up to 1ns/div. Minimum triggering bandwidth 250MHz. Protected 50 http://www.kandelelex.com/jpegs/tek2445.jpg in stock
Tektronix 2445A Portable Oscilloscope Similar to the 2445, the 2445A incorporates several new features to make them far easier to use. AUTOSETUP enables you to get the waveform on screen quickly and easily. SAVE/RECALL memory for 20 complete front panel setups and SETUP SEQUENCING capabil http://www.kandelelex.com/jpegs/tek2445a.jpg in stock
Tektronix 2445B Portable Oscilloscope Similar to the 2445A with an increased bandwidth to 200MHz and improved features. http://www.kandelelex.com/jpegs/tek2445b.jpg
Tektronix 2465 Portable Oscilloscope Similar features of the 2445. Bandwidth: DC to 300MHz; Features 4 traces, delayed sweep, CRT readout with delta volt and time cursors, 2mV/div sensitivity, and 500ps/div sweep. http://www.kandelelex.com/jpegs/tek2465.jpg in stock
Tektronix 2465A CT Oscilloscope / Counter-timer Same as 2465A, plus CTT/WR (option 09), GP-IB (option 10), and 2 additional probes (option 22).
Tektronix 2465B Portable Oscilloscope Four input channels, 400MHz bandwidth. AUTOSETUP enables you to get the waveform on screen quickly and easily. SAVE/RECALL memory for 20 complete front panel setups and SETUP SEQUENCING capability for stepping through a series of measurements steps ea http://www.kandelelex.com/jpegs/tek2465b.jpg
Tektronix 2467B 400MHz Oscilloscope Brighteye Display Similar to 2465B, but has enhanced writing speed 4cm/ns. 500MH trigger bandwidth, 875ps rise time, 2mV to 5V/div vertical deflection, 5ns to 500ms/div sweep speed.
Tektronix 2710 Portable Spectrum Analyzer Frequency range: 10KHz to 1800MHz; Resolution Bandwidth: 3, 30, 300HKz, and 5MHz. Maximum Sensitivity: -117dBm at 3KHz RBW (-129dBm with built-in preamp). Features: 80dB dynamic range, four-trace digital storage, direct-reading 50 ohm and 75 ohm opera
Tektronix 2712 Portable Spectrum Analyzer Frequency range: 9KHz to 1.8GHz with 5x10(-7) accuracy. Resolution bandwidth: 300Hz to 5MHz. Sensitivity:-127dBm(-80dBmV):-139dBm(-92dBmV) with preamp on (to 600MHz). GP-IB standard. Option 12 Quasi-peak detector (includes 200Hz,9KHz,120KHz EMC filt http://www.kandelelex.com/jpegs/tek2712.jpg
Tektronix 284 Pulse Generator Pulse output: 70ps or less rise time with a pulse width of more than 1us and a rep rate of ≈50KHz. Sine, square, and trigger outputs. Amplitude: 10mV, 100mV, or 1V into 50 ohm.
Tektronix 3002 Prism Logic Analyzer http://www.kandelelex.com/jpegs/tek3002.jpg in stock
Tektronix 335 Portable Oscilloscope Compact unit provides dc to 35MHz bandwidth, dual-trace, delayed sweep. Vertical sensitivity: 1mV/div (25MHz). Operates from AC or DC power source. 10.5 pounds.
Tektronix 370 Programmable Curve Tracer Provides 16 device tests on diodes, bi-polar transistors, FET 's, thyristors, opto's and IC's. Currents to 10 amps and voltages to 2000 volts in 10 steps. Completely programmable, digital storage, GP-IB control,and bubble memory. http://www.kandelelex.com/jpegs/tek370.jpg
Tektronix 370A Curve Tracer High precision measurements of semiconductor devices: 2000 volts, 10 amps up to 220 watts. Measurement Resolution: 1nA and 2mV. Provides 16 device tests on diodes, bi-polar transistors, FET 's, thyristors, opto's and IC's. Completely programmable, di http://www.kandelelex.com/jpegs/tek370a.jpg
Tektronix 371 High power Curve Tracer The Tektronix 371 is a Programmable High Power Curve Tracer used for testing a wide variety of power semiconductors. The industry standard 371 curve tracer provides dc parameter characterization of transistors, thyristors, diodes, SCRs, MOSFETS, optoelect
Tektronix 371A High Power Programmable Curve Tracer The 371A, the industry leader in high power curve tracers, is used for testing a wide variety of power semiconductors. It performs DC parametric characterization of thyristors, SCRs and power MOSFETs.

The high voltage collector mode permits testing the
Tektronix 465 Portable 100 MHz Oscilloscope DC to 100MHz bandwidth; Features include dual trace, 5mV/div to 5V/div vertical, 5nSec/div to .5S/div horizontal, delayed sweep, trigger view, and 8 x 10 cm CRT.
Tektronix 465B Portable 100MHz Oscilloscope DC to 100MHz bandwidth; Features include dual trace, 5mV/div to 5V/div vertical, 5nSec/div to .5S/div horizontal, delayed sweep, trigger view, and 8 x 10 cm CRT. This is an upgraded version of the reliable 465 with improved trace selection which allows
Tektronix 466 Portable Storage Oscilloscope DC to 100MHz bandwidth; Features include dual trace, 5mV/div to 5V/div vertical, 5nSec/div to .5S/div horizontal, delayed sweep, and trigger view. Stored writing speed 3000 div/us(1350 cm/us) reduced scan mode. Variable persistence and fast mesh mesh
Tektronix 466 DM44 Storage Oscilloscope Bandwidth: dc to 100MHz.
Tektronix 475 Portable 200MHz Oscilloscope Bandwidth: dc to 200MHz; Calibrated deflection factors from 2mV/div to 5V/div; Dual time base: 0.01us/div to 0.5s/div, 10x multiplier extends max sweep rate to 1ns/div; 1% time base accuracy; Trigger view; 8 x 10cm CRT.
Tektronix 475A Portable Oscilloscope Dual trace with DC to 250MHz bandwidth. 5mV/div to 10V/div vertical. 1nS/div to .5 S/div horizontal, delayed sweep, 1% time base accuracy, and 8 x 10 cm display. http://www.kandelelex.com/jpegs/tek475a.jpg
Tektronix 475A/DM44 Portable 250MHz Oscilloscope Dual trace with DC to 250MHz bandwidth. 5mV/div to 10V/div vertical. 1nS/div to .5 S/div horizontal, delayed sweep, 1% time base accuracy, and 8 x 10 cm display. "DM44" option provides differential time delay as well as DC voltage, resistance, and t
Tektronix 492 Portable Spectrum Analyzer Frequency range 50kHz to 21GHz. Expandable to 220GHz with external mixers. Resolution bandwidth: 1kHz to 1MHz. Reference level range: -123dBm to +40dBm. Dynamic range: 80dB. CRT readout of front panel settings.

Call for price and availability o
Tektronix 492BP Programmable Spectrum Analyzer Center frequency: 10KHz to 21GHz internal mixer, 325GHz using optional WM490 series mixers. Built-in frequency counter gives 1KHz@1GHz accuracy. Resolution Bandwidth (6dB): 100Hz to 3MHz. Frequency Span/Div Range: 0Hz, 100Hz to 10GHz (up to 10GHz in http://www.kandelelex.com/jpegs/tek492bp.jpg in stock
Tektronix 494AP Programmable Spectrum Analyzer Center frequency: 10KHz to 21GHz, 325GHz with optional WM490 series mixers. Frequency counter resolution 100Hz at 1GHz and 1x10(-7) accuracy. Resolution Bandwidth (6dB): 10Hz to 3MHz. Frequency Span/Div Range: 10Hz to 10GHz. Other features: Digital
Tektronix 494P Programmable Spectrum Analyzer Center frequency: 10KHz to 21GHz internal mixer, 325GHz using optional WM490 series mixers. Built-in frequency counter gives high resolution and accuracy of center frequency to 325GHz. Resolution Bandwidth (6dB): 30Hz then 100Hz to 1MHz. Frequency Sp http://www.kandelelex.com/jpegs/tek494p.jpg
Tektronix 50M30 Digital Input / Output Card Used in MI5010, provides 16 I/O lines in decimal, binary, or hex formats.
Tektronix 50M40 Data Acquisition Card
Tektronix 5110 Oscilloscope Mainframe DC to 2MHz. Holds up to three 5000-series plug-ins.
Tektronix 520A NTSC Vectorscope Graphically displays the phase and amplitude of TV chrominance signals on polar coordinates in a vector presentation; measures luminance amplitude, differential gain and differential phase. in stock
Tektronix 528A TV Waveform Monitor Monitors signals from camera outputs, video system output lines, transmitter video input lines, closed circuit TV systems and educational TV systems. Two 75 ohm loop-thru switch-selectable inputs with deflection factors of 1 and 4V f.s.; frequency resp http://www.kandelelex.com/jpegs/tek528a.jpg in stock
Tektronix 5440 50MHz Oscilloscope Mainframe 50MHz mainframe holds up to three 5000-series plug-ins.
Tektronix 576 Curve Tracer General purpose, "Industry Standard", system features: Big 6-inch CRT; Auto scale-factor readout including beta/div and gm/div; 3 collector supply modes; Auto positioning and polarity tracking; Pulsed based operation; Calibrated display offset with mag http://www.kandelelex.com/jpegs/tek576.jpg
Tektronix 577D1 Storage Curve Tracer General purpose tester measures DC parameters for 2 and 3 terminal semiconductor devices. Characteristics: 6.5 to 1600 volts; .2nA/div to 2A/div collector current; 5mV/div to 200V/div collector voltage; 5mV/div to 2V/div base voltage; Up to 100 watts.
Tektronix 577D2 Curve Tracer General purpose tester measures DC parameters for 2 and 3 terminal semiconductor devices. Characteristics: 6.5 to 1600 volts; .2nA/div to 2A/div collector current; 5mV/div to 200V/div collector voltage; 5mV/div to 2V/div base voltage; Up to 100 watts.
Tektronix 5A13N Differential Amplifier DC - 2 MHz 1mV - 5V /div in stock
Tektronix 5A15N Single-Channel Amplifier 2MHz 1mV - 5V/div in stock
Tektronix 5A18N Dual-Trace Amplifier 2MHz 1mV - 5V /div in stock
Tektronix 5A19N Differential Amplifier 2MHz Offset in stock
Tektronix 5A22N Differential Amplifier 1MHz 10mV in stock
Tektronix 5A38 Dual-Trace Amplifier 35MHz 10mV in stock
Tektronix 5A48 Dual-Trace Amplifier 50MHz 1mV in stock
Tektronix 5B10N Single Time Base 100ns - 5s in stock
Tektronix 5B12N Dual-Time Base 100ns - 5s Delay in stock
Tektronix 5B42 Scope P / I Delaying Time Base 10ns - 5s in stock
Tektronix 5L4N Spectrum Analyzer Plug-In Frequency Range: 20Hz to 100KHz. Resolution Bandwidth: 10Hz to 3KHz with auto resolution. Features: built-in tracking generator; selectable input impedance(1M ohm, 600 ohm, 50 ohm); balanced or single-ended input; 20Hz to 20KHz Log sweeps; 80dB on-scr in stock
Tektronix 603A Scope Storage Monitor in stock
Tektronix 73A270 VXI Arbitrary Serial Pulse/pattern Generator 2ch
Tektronix 751 BTSC Aural Modulation Monitor/Decoder Precision modulation monitor for entire BTSC sound channel including SAP and PRO.. Simultaneously displays all components necessary to assure modulation remains within legal limits. Bars feature peak indicators with timed peak hold and limits with dig
Tektronix 751 F40 BTSC Aural Modulation Monitor / Decoder Precision modulation monitor for entire BTSC sound channel including SAP and PRO.. Simultaneously displays all components necessary to assure modulation remains within legal limits. Bars feature peak indicators with timed peak hold and limits with dig in stock
Tektronix 7603 Oscilloscope Mainframe DC to 100MHz; Rise time: 3.5ns; Hold up to 3 plug-ins.
Tektronix 7603R Oscilloscope Mainframe Rack Mount DC to 100MHz; Rise time: 3.5ns; Hold up to 3 plug-ins.